mower

Hello I have an lt2000 19.5 horsepower hp Craftsman. The mower deck is a 42-in cutting with deck. For more than a month I've had the deck separated from the frame of the mower. I have replaced both spindles I have replaced the large idler pulley, I have replaced the small idler pulley. I...

My 54 inch Bad Boy MZ Magnum zero turn riding mower quit on me. It's model BMG5425KO. I turn the key and it just clicks. Battery is good. When I jumped/shorted the starter solenoid, it cranks. I thought it might be a bad starter solenoid, so I replaced it since I had a spare one. Still nothing...

The murray riding mower I have will not all even crank. In the wiring system from the wiring harness to the alternator wire the connecting wire has 3 wires and one of those wires is black which would indicate that might be a ground but I'm unsure of where it goes. Any help is greatly...

My Bad Boy MZ Magnum runs for about 20 mins then stops. It starts to sputter like it's running out of gas then quits. I have a full tank of gas in it. I'd let it sit for about 10 to 15 mins, start it again and the same thing happens. Runs for a bit then quits. Fuel pump? Fuel filter? Carb issue...

When I use our Honda gas mower to mow the lawn (dry), grass does not sick to the periphery of the inside of the mower. But when using our Ego electric mower, the grass does adhere. This causes clumps of grass to fall on the lawn. I've cleaned the inside and made sure it was dry, but the...

I have a toro mower from about 2013. I stored it without any gas thinking this is better than with gas and a bottle of ethanol added in. Well, I wound up having a family member give us a Honda mower that was in great condition and worked so over the years I used the Honda instead. The empty...

Hi I have a husqvarna yth1842 with a B&S 18.5 intek engine(33R777-0003-G1) I put new pulleys and spindles on it last week, it was running and mowing great until Sunday and it just died while my Mom was mowing. Now it won't start,it turns over but when it kinda cranks it sounds like a small...

I am going to buy a new mower but looking for something that goes forward and reverse with the foot pedal and not having to do anything else like my old Murry, is there such a thing out there anymore ? Thanks

I have a Honda HRR2167VXA mower that has recently developed a bad vibration. The blades have been replaced, so I do not suspect that to be the issue. The vibration is worse when the mower is started up, and it smooths out some when the blade is engaged. The self propelled drive seems to be...

Hey was just looking for some recommendations on a new 0 turn mower. My old Craftsman tractor/mower finally broke after 20 years. But was looking for a new 0 turn mower kinda leaning towards the hustler raptor xl but any suggestions would help thank you.

I have a John Deere Z345r zero turn mower that blows the PTO fuse every time I start the mower, without actually engaging the PTO. I have taken a look at the wiring haven't found anything damaged, I unplugged the clutch, and it still blows a fuse. I have not been able to find a wiring diagram...

I finally got the drive belt in place! Then I had to straighten a bent bracket and add two washers for a pulley to get lined up. Was able to get the motor running, I went for a drive and everything looks, feels and smells like it’s all good! NOW I’m back to the motor won’t start! Has my engine...

I have a John Deere D125. 9 years old. About 250 hours on it. It broke the deck belt. I replaced the PTO cable as old one was stretched. I replaced the housings over the deck pullies because belt wore threw right side cover. I replaced left spindle bearings because they were little noisy...

I've got a 9360600 Series Ariens Riding Mower with a 42" Deck. The belt is supposedly 954-04060 which is a 1/2" x 95.5" belt. If I put a 1/2" x 95.5" belt on the mower its too loose. The blades will spin, but it takes a while for them to get up to speed and in grass they stop. A 95" belt is too...

I have an old Toro Recycler 22 inch self propelled mower. it runs great but the handle bar is way to low. I'm hunched over while using it. Does anyone have any ideas for the best way to fix this? I considered cutting the bars and rewelding them up at a slight angle, but it's a pretty janky...

For fuel do you check in the carb throat somehow or just check the plug? And is it enough to use carb cleaner to just get it popping a few revolutions to confirm you have spark?

I just purchased an old yellow deck JD STX38 in near perfect condition. The battery is probably not the best but a few days after charging it is able to start the tractor. When I tested voltage was at 13.6 while running. After about 20 minutes of mowing the battery is completely drained. How...

Looking for recommendations on keeping grass build up under my 54” deck. I have heard of a product call Slick Plate has any one used this or something like it.

Anybody got any idea of a reasonably priced mower or lawn/yard tractor that can cut grass on a steeper lawn AND push a plow or blower in the winter? My 25 year old rear engine rider has hard to find parts, and my 20 inch Ariens snow blower was bought 20 years ago when we lived in northern...

I was mowing, everything worked great. Suddenly the PTO mower disengaged, quit cutting grass. So I rode the mower back to the driveway, which is about 50 yards from where the mower deck quit. I checked to see if something out of order. I tried to restart the Toro, only clicks at the starter...

How hard is it to replace the brakes or what stops the riding mower when you press the clutch brake? The one seems to roll passed the brakes as if there isnt any from when it was purchased new and would directly stop. Murray 425008x

All of my usual questions have been answered by reading other people's posts, but not this one. I have a John Deere Zero Turn mower, model Z930M (54" cut). Bought it used but not cheap. Now at 1,200 hours and I use it for a three-acre field and 2-acre lawn. Once I learned how to turn without...

While mowing today, the mower (Model 3661 with powerfold) just quit. Tractor was running fine. Checked the torque on the blades and it was correct at 55 pounds. Checked the PTO 10 amp fuse and it was ok but I replaced it anyway. As I quit working on it I noticed the light switch was on but the...

The Self-propelled Drive Disk turns fine but the belt from the Transmission to the wheel slips. The Briggs Engine is 4HP as noted in title. The throttle cable rubbed on the Engine shroud and wore the stamped numbers off. I am guessing Mower from the early 80's. But with no Model numbers, not...

52” Gravely Pro-Stance mower with loss of power, to the point of almost stalling, after engaging the mower blades. Its got a 19-HP Kawasaki engine. The mower is non-commercial. I only use it to cut my lawn once a week. Gravely started manufacturing this model Pro-Stance mower in 2006...

Hi, I have a Honda HRN216VKAD, with the GCV170 engine bought new in the box from Home Depot on line this year. The engine model is GJAUA 2361122MY03 with a punch mark on the data plate and blue dot so the recalled camshaft on these engines was done I assume at the factory, Runs great, it leaks...

There is a 70” Gravely Triplex Hydro Reel Mower for sale locally. Are parts still available for this thing? I've experimented with a push reel mower on a small area of my lawn, and I like it. But my lawn is too big to mow with a push mower. This would fix that.

Hi, I have a Mountfield MTF 84H riding mower. Does anyone know the best way to put a drive belt that's come off, back on? Any suggestions welcome!

I inherited an old Scotts Intex Edge self-propelled lawnmower, (though a Google search also turned up "Intek" in addition to Intex),) 6.5 HP OHV. The plate says S014255730423 and Code 9047M. The customer service number on the plate is for Briggs & Stratton, not the lawnmower itself...

Greetings! New member here. A neighbor was gifted the above referenced mower; told me it started and ran fine for at least one lawn mowing (and many years with previous owner), then she filled with some bad/old gas and it hasn't worked since. I offered to go into it for her, believing with all...

I have replaced the alternator/stator, voltage regulator, ohm the wiring all check good, 32 Volts ac coming out of Stator, 1-3 volts dc coming out of regulator. any help? Briggs and Stratton 23hp vtwin

I had the good fortune, maybe the misfortune, to acquire a Troybilt sickle mower. Actually looks new. Story is it was purchased and never used and left in a shed for years. Story does match appearance of the unit related to paint finish throughout, all labels and decals, tires, cables...

Hey everyone, I’m currently in the market for a new lawn mower, and I want to make sure I choose the right size and type based on the actual size of my lawn. I’ve seen a few online tools and guides that help "calculer surface" (calculate area), but I’m curious how most of you go about...

Does anyone know what the part number for this bolt/pin is? There is suppost to be one on each side of the mower deck and it holds the back side of the deck up. I need to buy another one because the person that gave me the snapper mower lost one of the pins. Let me know if the picture of the...

New guy here. Does anyone know what the model was or have any information on a Ferris mower that is a 32” Stand on style with an adjustable seat? I have researched everywhere I can think and have not been able to find any information on what this mower is. Any information that anyone has would...

I have this older Snapper that still starts on the first pull. I need to replace the drive belt. I also need to change the oil and air filter. Where should I go to find the parts? A manual I found online didn't tell me the kind of oil I should use. IIRC (not a sure thing at 83) I used 30W...

So. I have a Craftsman Riding mower and its rear differential won't unlock and I need to move it from where it currently is. But the rear differential will NOT unlock at all! it shifts and the neutral lock moves but doesn't work. Please help me quickly. Thank you!

I bought a used Hustler Raptor 42 & former owner had a mulching “kit” installed by the dealer but I’ve noticed the brackets on my mower deck are different than the one in parts manual & attach by only 3 places not 4 connected to the height lever. The attaching bracket bolts are very long on mine...

I purchased a new B&S 163 cc engine a few months ago, and I'm finally getting around to installing it. I don't know how to get the belt pulley off Can someone help?

Hello, This is my first riding mower so I’m learning a lot. We started using this in 2019. I don’t have a nice flat lot. We have 3 1/2 acres out in the country. Probably the majority of what I cut is flat, but the steering is used a LOT! There are many areas with angles/ruts/slopes that test...

Just wanted to know opinions concerning parts sourcing. I occasionally work on mowers and usually the focus is on the mower deck: spindles, pulleys, belts, etc. I've ordered original equipment replacement parts and parts from Amazon. I do not really see a difference and have not had any failures...

I've got an almost 30 year old Toro 20449 (GTS2 - SN:7901137) that doesn't seem to have the power it once did. I can't find an engine identifier anywhere, but it's a 5 hp Briggs. I bought it new and have only put and hour on so per year on it as I only use it to mow one hill. Even though the...

I'm looking at an older Bolens tractor with 11hp Briggs, tractor looks ok but it's missing the mower deck. Wondering if these tractors need a specific Bolens deck or if another brand could fit instead!?

I have a 2012 year Bolens 500e 140cc lawnmower that will not start. It has a new plastic carburetor, airfilter, and cleaned out flushed has tank. The mower makes good spark but the only way to get it to run a few seconds is to put gas into the spark plug hole (will run for 2-3 seconds) or...

Does anyone have any suggestions on how to acquire a platform for a spray tank on the front of a 72 in. Scag? I asked the dealer but they apparently don't make any such attachment. Times like this I wish I had learned how to weld.

I have a totally rebuilt Dixon mower for sale, whole or parted out. I got curious about these mowers, their propulsion system, and history and ended up restoring this 30". Shipping the complete mower is probably a reach but i would entertain parting it out for shipment that way.

mower with autochoke runs for 3-5 min and then stops?? i cleaned the carb and linkage.

My transmission part number is 589600601. On the shaft that the wheels connect to, I see evidence of grease on over half of the outside of the black case. I'm not sure what signs to look for that the transmission might be on its way out.

Hi all, I have been considering a robot mower for my garden - with an area under trees i was at the kingsbridge show today , and they had a stand for robot mowers autocut the company and they are exclusively Husqvarna and robots only They seemed to know a lot and answered questions which i knew...

Push mower built from 5 different mowers . Long before string trimmers and those weren't needed with this mower . It would suck tall grass / weeds from a fence . The only part new was the blade . The reason it worked so well was the deck was a donut looker , the blade missed the deck edge by...

Hello, I suddenly noticed a tightness in a specific point while turning the steering wheel. I raised it up and found one wheel connector to ‘axle’ problem. This is my first riding mower so I’m learning all about it! Please let me know of any other front end parts that I might need to look at! I...

Hello everyone, I recently got an exmark mska21b lawn mower for $5.00 at an auction as a non-operable. Turns out it just needed a carb cleaning and it fired right up with only a half hour of tinkering. It work great, and I want to give this to my dad as it is better suited for the larger...