model

This engine is on a craftsman riding mower and will only run for 20 minutes from cold, and then 15 minutes after a 20 minute cooldown. Heat seems to be the issue. Have checked oil, airfilter, cap, plug and changed away from ethanol gas. It literally just dies…no rough running at any time...

Trying to remove the drive pulley and wondering if the pulley has to be unscrewed or just removed by heat and tapping. There are threads visible inside the bottom of the pulley but nothing I can find says it has to be unscrewed. There is no bolt from the bottom. Possibly it fell off but it's an...

I purchased a Pulsar 21" 200cc Gas Push Lawn Mower from my local Menards (https://www.menards.com/main/outdoors/outdoor-power-equipment/lawn-mowers/pulsar-reg-21-200cc-gas-push-lawn-mower/ptg1221drm/p-1642874304916526-c-10112.htm). I've had it for a year, and so far, it's been a pretty solid...

Working on a "very experienced" Yard Man 38"/12.5 HP B&S The model on the tag under the seat is: 13AT674G401(the seat must be from another model MTD) The tractor has a totally different deck belt/pulley arrangement than what is illustrated in the MTD website. This tractor has the cable...

I am attempting to repair an old Ferris 36 inch walk behind. It has a Kawasaki FC401v engine. I removed the head and found both push rods not in contact with the rocker arms, and that the exhaust valve was stuck. I removed the head and removed the exhaust valve cleaned up the valve shaft and...

Hi all, I need to replace the fiber washer in the photos....it was destroyed trying to get the pinion gear off the axle. I have researched extensively on line with no success....no parts diagram of this model shows any washer at all for this model. Can I just use a fiber washer that fits the...

Ladies & Gentlemen, I seek your wisdom. My mower will start fine but when cold it takes several minutes of sputtering and puffing black smoke to decide to speed up and run. It has new carb, coil and plug. Once it warms up and starts first pull every time and runs fine.

Working on a Model 934778 60". The mower had a broken drive belt. I replaced the "broken" drive belt and the idler pulley. The belt, cogged, look hardly used, and the idler pulley bearing was tight. I put a new belt(cogged) on along with a new idler. I started the mower up, warmed it up a...

I’m interested in buying a TS148XK Husqvarna riding mower. I found a dealer who has one, my concern is this mower has been sitting crated in his warehouse since 2023 and he says it was factory assembled in 2022. I’m concerned it’s not a “new mower” in that it’s been sitting for so long. He’s...

This has happened repeatedly. The mower has 308 hrs, purchased new in 2022—home use. Stored in a dry shed. I have checked all the wiring I can, loosened, examined, and retightened the ground on the engine. I tried, but without success, to pull apart the electrical clutch connection to check the...

I've got one of these electric trimmers - motor works fine but the tap-to-advance stopped working ages ago. I can find no help online - there are similar discussions, but the photos show a mechanism that doesn't look like the inside of my trimmer (photos of the inside and the spool attached)...

A couple of years ago I was given a Sears 917370431 self-propelled lawn mower from my neighbor. This started up fine and performed well, even though I'm not a great fan of its self-propelled feature, but that does work. Anyway, I recently hurt my right shoulder and have discovered I have pain...

Just replaced the belt on the above model, and noticed when I took all apart that the blade driver has no protrusion inside to fit the key way on the drive shaft. Just wondering if its sheared as I see no evidence of there having been one ....perhaps this is why it's not self propelling? Should...

Engine on a Husqvarna 46in riding lawn mower. After replacing the carburetor I have had issues with surging and idle. The replacement is not an exact model but very close. Initially, the engine would constantly surge when not under load. It also didn't seem to run fast enough. I reset the...

Unable to remove gas tank on craftsman push mower model 917377582 Seems to be a fastener i can't find. No luck utube.

Hi all, Just replaced the belt on the above captioned mower, and made sure all bolts were tight, however the rear left wheel keeps loosening and falling off. I suspect that the threads on the pivot arm may be stripped,but it shows no sign of this visually.....anyone else had this problem or have...

Troy-Bilt Lawn Mower Model 11A-B2RQ711 S/N 1D117K02798 has Honda engine and engine cover states TB130 XP My neighbor gave me this mower, as he hadn't used it in years as he's replaced his grass with rocks. I added gas, cleaned the air filter, started it up and it runs good. However, he...

Model 8237 Ser 9424117. I am trying to save this one from the scrapyard. I pulled the engine and disassembled. Replaced bearings and seals top and bottom of crank and the drive shaft bearing and seal. Light hone of cylinder just enough to clean it up and put the crosshatch back in it. New...

First time poster hoping for some expert advice. I believe that I've sheared a woodroof key on the flywheel, I have spark, fuel and compression so timing is the only wildcard at the moment. I'm hoping for some advice or instruction on how to remove the darn plastic flywheel shroud so I can pull...

It has no ID plate on the frame, even though most of the factory labels are still on it. IDK what year or model it is to start looking for replacement parts. I've tried searching for "snapper zero 52 parts", but the only results I've found don't look like mine. Specifically: 2 pumps with 2...

The stamped model information on the rocker arm cover is no read able butvI have a photo of the serial number attached Thanks in advance, bartles

MRP216015B The Driven Wheel shaft was worn as were the snap rings. The "Shim" washer was missing. I am waiting for the shim washer. What is the purpose of the shim washer (29)?

Asking for confirmation the resistance reading for a good blade clutch should be 2-4 ohms, right? Thanks in advance, bartles

I can't figure out where this yellow wire? Look at the picture and you'll see the seat safety switch and one yellow wire that looks like a wire connector. I looked inside the Murray where it is located and nothing. Nothing on diagrams. I can't get it to start or turn over. I checked the battery...

I have a Toro I think it’s a recycler model , number 20381. I have a bad transmission on this lawnmower and I can’t seem to find a replacement. Is there any transmission will fit in this lawnmower that I can replace the one that I have? this is a rear drive lawnmower. Is there some transmission...

I have this Timemaster mower and while I think it's a great mower I cannot figure out one thing. Serial number starts with 313. I have replaced the pulley on the blade shaft where the belt on it goes to the engine, the shaft, and the spindle. The pulley was held tight by a locknut and under...

Hi everyone, I'm a new member. Thanks for the add. I have a craftsman edger (#247.772460) with Briggs & Stratton engine #10T802 0711 B1. I am able to start it after putting a new carburetor diaphragm and gasket. My problem is that it won't stay running and stalls out. I can get it to stay...

Well, the title sums it up. I have the mower in the shop and the guy says parts are back-ordered from the factory. Been a week or so. Probably will never come in I guess. Tried to find something on the 'net before coming here. No luck. Any ideas? Thanks.

I am using a multi-meter to determine if my sparkplug is not working on my Murray snow-blower. I cleaned the carb last year and it worked fine. However, this year when I pull and even when I use the Electric Starter, I cannot get it to work. Spark plug testing : from the videos I watched, it...

Hey guys, Im looking at a John Deere LX188 to put some work into and have for a second mower. The one Im looking at needs a hood / seat and some mechanical work with the fuel system. What do these go for in this condition and what do they go for with no issues ? Are there any things I need to...

Looking where to buy a used 18 hp kohler motor. On my cub cadet snow blower tractor. Preferably in 518 area. Thank you for any help!

The mower cranks but will not start. I've cleaned the carburetor and the fuel tank. I also removed the fuel solenoid (needle works fine). Replaced the spark plug and the air filter. Still cranks but will not start. What else can I try?

I have a wire that connects from the stator or alternator that is dual charging. the wire that I have that connects back to the chassis wiring harness has 3 wires one orange and yellow that connects to the engine wire connection. then there is a black wire that was not connected when I took it...

I picked up a lot of 7 riding lawnmowers in different stages of disrepair.. In this lot is a Craftsman LT2000 with a Kohler 17.5 HP engine and hydrostatic transmission.. My issue in continuing is with the transmission.. Should I continue that discussion here or once I figure out what I have...

Hi I bought a skid Steer Loader Shing Heung, model Cow 5000, year 2006 I know that this a lawn mower forum but anyone can tell me where could I get all the manuals? I do not find them. Thanks! R

Started some work last year on the motor on my L120, didn't keep track of the bolts to reattach the intake on both sides.... Grrr, just get a ziploc baggie... anyway everything is basically a 10mm head but a 1/4-20 bolt seems to fit really well. I'd like to keep everything oem but not if I...

I just acquired a JD front tine 24-inch wide tiller with a B&S 1987 5HP flathead engine. It looks like everything is mechanically sound so I intend to restore and flip it. I've got the B&S numbers off the engine shroud but have no idea where to look for the JD model and serial number, which I...

Hello Just recently got an old countax c300h . That needs a set of belts. The numbers on the stickers say 90812 3b622 2983(C). What I can make out from Google is the first numbers are the date backwards. So that would make it a 2009 model. What I need to know. Is the (C) for series C . And when...

When I increase the throttle the engine speeds up but the tractor will not speed up. I put a new drive belt on it last year. Any help would be appreciated. Thanks

I have a totally rebuilt Dixon mower for sale, whole or parted out. I got curious about these mowers, their propulsion system, and history and ended up restoring this 30". Shipping the complete mower is probably a reach but i would entertain parting it out for shipment that way.

Is there another way easier way to get this connecting rod screw with a torque head out, so I can get this piston out.

Heard a click when I went to start it. solenoid was bad. Replaced.Now it turns over. But no spark when cranking but got a spark on run position. What’s up? HELP PLEASE!

There is a small amount of lateral (side to side) play on the counter balance (Marked A in the pictures) if the crankshaft is reversed by hand after assembly . The small bracket underneath A moves correctly when the crank is rotated in the correct direction only. The bolt is torqued to 115 inch...

Runs strong, looks great. Carb, fuel tank and primer cleaned, new float valve needle and seat installed, pilot jet upgraded to B&S 108308 spec, air filter cleaned and oiled, blade freshly sharpened, drive belt inspected/checks good. Non-ethanol fuel and AMSOIL Dominator oil mixed at 40:1. Starts...