carb

Here is video of the machine in question. Funny thing is, on video it doesn't really sound like it's doing anything. But in person, its definitely running rough. You can see at the end of the video, how the handle is vibrating. Ok so the backstory. This is a trash rescue. It was overfilled...

Generator unit is about 14 years old Briggs & Stratton Storm responder 8250. Always run clean gas through the unit and use stabilizer. Change it every 6 months. This year it had all the signs of crap in the carburetor. I went to take the bowl off to give it a good cleaning and it's held on by...

I bought a Dixie Chopper with Generac 27hp knowing there was a fuel supply issue. Engine ran fine at idle but ran rich as rpm's increased. Verified choke and air filter were fine. Presumed the Nikki dropped a main jet or two. When I opened it up, in fact the main jets were not in place, nor...

Oil coming out of the carb compartment breather tube. Any suggestions?

Newbie here, I put a new carb on Husq YTA 24V48. Throttle linkage seems to be fine, and pulling it back to low does slow it a bit, but not nearly as low as it should be. Is this some kind of governor adjustment, or what??

I am replacing the carb on a D130 John Deere Riding lawnmower. Are there any diagrams or photos to guide me how to reinstall the two rods attached to the carb? Thanks in advance.

I have a Trail Blazer Sickle Bar Mower with a Briggs 4 hp engine. I"ve had it for years but really never used it very much. I decided to bring it to life recently. I found that the gas tank with carb attached was the main problem for starting and running. So I bought a used carb and tank with...

I have a Kohler command pro CV730S. It is burping back the carb (puffs of gas vapor coming out the carb) at idle. Seems like a valve problem but it is supposed to be hydraulic valve lifters. No adjustment. loses power under load in heavy grass and uphill. But not every time. I did a governor...

Engine model:123K02-0193-E1 Primer button type carb I've replaced the float, needle valve, and the needle valve seat using all B&S genuine parts. From bench testing everything looks great; I test that everything seals right on the bench by turning the carb upside down and drawing a 5psi vacuum...

Greetings all. New here. Father in law gave me this snowblower 20 years ago. 8hp Tecumseh. Think he had the JD dealer on speed dial every year with carb problems. I ran it dry between uses and had no issues. Couple years ago had puddle of gas under carb when friend who owns small engine shop...

It's leaking with bowl on, but if I hold it up with bowl off it'll stop. I stretched spring, didn't help. Any fixing the accursed plastic apparatus?

Where the hose connects is a 90deg elbow. The elbow turns freely. It also leaks fuel. If I add epoxy, will it solve my problem or break off and leak again eventually??? TIA.

Toro mower 20065 - SN 280105976 It surges, kinda weak. Still gets the job done but not ideal. Thinking of swapping this one in. Don't know why I got it as it's not exact but that's what I do lol. Can I? Should I just prop it open somehow or anyone got a tip to make a custom switch? And how does...

I have an older Broadmoor...#1693840 with CV46016 hp Kohler . with a chi8nese replacement carb , the carb started flooding and belching black smoke when i was mowing the other day, finally quit 20 feet short of my garage. ordered a replacement chinese carb from Amazon... just installed it, will...

Does anyone know if there is a carb rebuild kit for Kawasaki 15004-0827 Carburetor (Goes on Fs600V)? I can find exploded view diagrams and the whole carb assy, but not a "rebuild kit" for it.

Hello, I have an Echo back pack blower, model PB580T and need to purchase a carb adjustment tool that would be able to get in the tiny recesses that the adjustment screws are in. I bought a cheap universal one and of course it would not work. The carb is A021004331. The box also says WTA_35.It...

22hp VTwin; New carb and new throttle cable assembly. Starts only if primed and runs full rabbit; cannot get it to idle. Any help? Thanks!

I have been gifted a non-running Honda EM 6500 sx generator. It has pull start and electric start capabilities. If I have no battery connected and just use pull-start, can I just cut off the plunger on the solenoid? The guy who gave it to me said it started easily with the pull start before he...

I have had a hard time starting my lawnmower and it would start but sporadically. I discovered that the choke valve lever on the carburetor was stiff, it moves but not easily. The valve moves but not easily. When I pull the choke it lifts the lever and closes the valve but when the choke is...

I have a problem. I’m working on my MIL’s Cub Cadet XT1 42” Model-13AVA1CS056 mfg- 2015 with a Kohler SV541 engine. The mower was working fine then on a restart the engine went to full throttle. The throttle control lever didn’t do anything. After looking it over, I noticed the throttle shaft on...

i recently upgraded a troy bilt rider with a knocking 18hp Intek...with a strong & quiet 20hp v twin. it is belching black smoke, after a carb teardown and immersed in my ultrasonic cleaner for 2 cycles... i have found clogged passages in the upper main body before, but this one is spotless. i...

Hi, I have a lawn vacuum with a 8.75 Intek B & S engine. The carb has this number on it. 7508S 26462. Can someone help me find a source for the cab. The engine has this number 7BSXS.2051HC 277317 Thank you

Hi everyone, I have 11.5 Briggs on a Troybilt ride on. 817807-0984-G5. It has a Nikki 799245 carburetor. The Nikki is playing me out. Does anyone know what Walbro carburetor replaces this Nikki 799245. Thank you, bruincup.

B&S 17 HP single cylinder starts with gas in air intake but won't keep running. REmoved carb and it had gas in it. Suspect the electric solenoid valve at the bottom of the bowl. That part is new to me. What does it do? I plugged the electrical connection with the solenoid removed, turned...

I replace the carburetor on my D140 John Deere because it was filthy and gave much trouble. The replacement wasn't OE but was very close to the same as original. I don't think that the choke is closing completely because it does not crank cold. I can put a little gas in the input area or even...

I have the above top-handle saw, and when it runs, it works great. But it's been getting more & more reluctant to stay running. I'm almost certain that the fuel diaphragm in the carb needs replacing. It's acting like it's starving for fuel. But I can't find a parts diagram or parts list with...

I have a John Deere trimmer that is quite old but still does the job but unfortunately it has outlasted parts availability, The model number is XT250B. I believe that it was manufactured for John Deere by Stihl. I need conformation of this assumption which would give me a starting place to...

People, I have an edger, with B&S engine Model 80202, TYPE 1830-01, CODE 87013103. 3 HP. I am not able to attach a picture as I am computer illiterate. Thats why I posted as link below to the diagram, carb is 4th page down on the link. The carb has a plastic tube with a very fine filter...

I’m looking for a diagram that shows the carburetor spring attach locations on a Gravely 260zH, 992135. My service manual doesn’t show this detail. My engine is running high low rpm’s, alternating about every 2 seconds. I found a spring curled around a rod and neither end is connected. I...

bought hr215k1sma in package deal along with several other hondas. mower looked almost new, but oil leaks into carb. oil level good. lot of gunk and stuff after changing oil(changed it 3 times and looks good now.) assumed it overheated and rings or something bad in engine. thought i would ask...

Working on a JD LX 277/ MOL277C061290 with Kawasaki Code FH500V-BS11: Owner was mowing when the fuel line from the fuel pump (or from the carb "overflow" line) to the carburetor evidently leaked fuel down to exhaust system starting a fire that melted the carb ground wire, overflow line, and...

I have a briggs 24 hp twin engne. I am cleaning the carb and when I took off the plastic float mechanism, a small jet fell out before I could see its location and orientation, In looking online at the diagrams, I still cannot figure it out. It fits in several differene spots. Does anyone know...

I have a Tvs100-44015b 3.5HP Tecumseh engine that I completely rebuilt last year. New crankcase and piston, valves,etc. Really runs great when warm but having trouble keeping it running when starting cold. I have to keep pumping the primer to keep it running. I am suspect of the cheap carb I...

Hi, I have an old Harrier 41 307R The gasket/rubber washer which is on the nut underneath the carburettor bowl has perished and fuel leaks from it. Just wondering if anyone might where i can get a replacement in the UK, or what size i need? Thanks Briggs & Stratton 127800-1959-01

Where can I get a high-altitude main jet for the carburetor? Need 6000 to 8000 FT.

I bought a used machine with a B&S 305 CC 1350 series OHV motor. It ran like a top, until I brought it home, filled the gas tank, and left it for a day. The carb leaked fuel all over the floor. After installing a carb kit, and trying to restart, it locked up on the compression stroke: turns out...

Hi All, Machine was running rough and when I dug in under plastic engine cover I noticed a boomerang shaped arm between the throttle and choke control doors was un-connected on the throttle end; (see first pic). A small brass-capped retaining pin was missing; (see arrow pointing to this in...

mower with autochoke runs for 3-5 min and then stops?? i cleaned the carb and linkage.

I went to Oder Gaskets for a carb, but when I looked it up, it said there is also a high-vent version. Can anyone tell me if I have a high-vent version? Engine Family YBSXS 2051HF 274479 carb stamping: 214731 and 5332 and 1930

Hi all, Have replaced fuel filter, lines, plug, air filter and carb on the above captioned blower.....it started at first after the new carb, but now will not start. Anyone have an idea what H and L should be set at for this blower? Currently both out at 1 1/2 turns. Thanks

Took carb off not sure where springs go

I don't know how it got opened up more but you can see that it is enlarged. If it causes a leaner emulsification can it be corrected with the adjustment screw. Or does that fixed jet that screws in straight down next to the adjustment screw control that mixture? That port and the Air Intake...

Howdy, I just replaced the carb/filter/plug. Changed oil, new gas. First pull, and she fired right up, but ran at full throttle & throttle adjust had no effect. It wouldn't shut off: had ta yank the plug wire. At this point, I'm assuming a linkage issue. I'll show pics & a video of me moving...

Cleaning out the garage and I'm getting rid of things I won't need. I have an old mower carb and metal fuel tank. Very little rust inside. I don't know what it is from. It was something my dad saved for about 30 years. See pics. If you want any more pics, let me know. There are no model numbers...

It's leaking with bowl on, but if I hold it up with bowl off it'll stop. Any fixing the accursed plastic apparatus?

It's leaking with bowl on, but if I hold it up with bowl off it'll stop. I stretched spring, didn't help. Any fixing the accursed plastic apparatus?