Search results

My 320 will not put any voltage to the small igniter wire going to the starter solenoid when the ignition is turned to the start position. Battery is at 13.1V. The safety switches are good. I can spin the starter motor by jumping the two large legs on the solenoid. I am reading in the manual...

I have a 1994 John Deere 320 that has been running fine. I did the cam swap two years ago. Now, once it warms up, it is popping out the exhaust, and loss of power. It was blowing black smoke also so I put a new OEM carb on it, cleared the black smoke but still popping out the exhaust. changed...

ZTR

Thanks

Thanks Would you happen to know what company builds them for JD?

what eXmark mower has the serviceable hydros?

What John Deere zero turn mower has the serviceable hydro?

Does John Deere make its own "john deere" engine?

Does eXmark make it's own "eXmark" engines?

thank you

What size is the key way that goes into the crank shaft for the PTO? Someone told me they could be standard or metric. It's one inch long. It has a Kholer engine

Nothing bad just a praise report, if you will. The DEKA battery on my 320 was installed in 2008. It's just now trying to give up the ghost. I am trying to find one just like it.

My LT 1024 Trans axle will lock up sometimes when I stop, kill engine, and get off mower. Go drink coffee and come back, start engine, and the mower will not move forward or reverse. I am stumped.

will a 1999 John Deere 345 with 20hp Kawasaki liquid cooled twin cyl have the "plastic cam gear"? thanks

Hey My 320 Lawn Tractor has the FD590V Kawasaki engine. What make a spark plug on one side flood out with gasoline? It starts running rough and all I have found when I took both plugs out was that one (left side) was flooded with raw gasoline. Thanks

Left side of my 2004 Laser Z is down to a slow roll. any advice on bench testing the pump and what are the pressures suppose to be? It's not getting air into the system. I ran a magnet into the oil tank and got very small amounts of metal. Any help would be appreciated. Thanks

when i shut the mower down, i am getting gas leaking into the cylinders. I put a rebuild kit in it two years ago. it has 1082 hours. FD590V Anny suggestions? Thanks

I have found a used Troy built TBE 515 edger for sale. are these units any good? It's a four stroke. Thanks

Hey guys and gals! Is the carb on my 320 lawn tractor worth rebuilding or just replace? It's never been off the tractor and It will not idle. If there is a rebuild kit for this carb, what is the part number? THANKS!

Hey guys! I would like to ask a question about the cut quality of my JD 320 48" deck. It leaves stripes like the blades are not close enough. I always ude John Deere blades. All spindles are tight. What are your suggestions?? Thanks.

I have a eXmark Lazer Z E series that i bought new in 2015. I'm thinking of selling. what's it worth? It has 86 pampered hours on it. Everything that has been done to the mower is in a file in my filing cabinet. thanks.

WOW~ I got my cam shaft, plus a LOT more swapped out yesterday. Man what a difference!

anyone know the specs on a Cub 1330? A buddy of mine just acquired one. the main thing that needs done is the rear end needs servicing. Also, can anyone tell me what rear end came in this mower from the factory? Thanks for your help.

Hey all! Is there any way to speed up my tractor in reverse? I changed fluid and both filters last year. It works fin other than I'd like it to go a little faster in reverse. thanks

having trouble keepeing a new cub belt on the deck. it's the correct size that cub calls for 1/2 x 103". all pulleys are tight and smooth. it's installed correctly. advice? thanks.

starter part number is 32-098-04. Can you replace the bendix or do you have to buy an entire starter? Thanks

thanks! it was hard work but well worth it.

i decided last year to remove fender and power wash the top side of the transmission. It was filthy!! No doubt I added ten more years to his life! I also washed the top of the engine too after removing the radiator and fan. It was a MESS!!

does anyone know which electric clutch is on a JD 320? I have looked on JDparts and it lists more than one. thanks!

my trimmer was made on 1996. there is another number SH20250B24BA i think. some of it is hard to read. can i buy the crankcase cover gasket ? i had gas leaking and had to take the plate off to get the gas tank off to replace the fuel lines. also, what size are the gas lines? thank you!

pros and cons of using seafoam in the engine and the gas tank.

thanks next time i have the deck off, i will do that. i painted the rest of it couple weeks ago.

what do you guys spray the underside of your lawn mower deck with?

i just read on another forum, that the plastic cam on horizontal engines are not a pron to fail. is there any truth to that? thank you.

I know that there has been problems with the plastic cam on some of these engines. My engine has 998.0 hours. I was wondering do I need to make plans to replace the plastic gear now or wait until it self destructs?

any preference on what type of led headlights you all have installed on JD lawn tractor?

what have you guys used when installing lights on the front of you Lazer Z?

Finally decided to take the deck off of my JD 320 and clean it for paint. only one little crack in the whole deck.