Search results

John Deere I rigged mine so the Reverse button stays pushed down.

You take the wife's best big sharpest kitchen knife and place the sharp edge on which side of the gasket you like . Then you use the hammer to tap -tap - tap the back edge of the blade . If necessary work around .

try this Using a sprinkler about 3/ 4 inch tall , so the blades don't contact it , put it under the deck and at full throttle run the blades for a minute or two then move the tractor so another area is cleaned etc.etc. With a little skill ya won't get wet . I find that easier than connecting...

Has a verdict been reached ? If not , is it still within the warranty period ?

JD X350 with 180 hrs. running so bad while mowing i didn't think it would make it back to the shop . Pulled original plugs and replaced with what the Auto supplier referenced the NGK to Champion that I ask for . I;ve never had a engine start so fast when the 1st piston went to compression .

If you've failed to maintain the under side as i do and it's dried , mow wet grass for a couple hours to soak the dry then a water hose with a good multi - pattern nozzle works well to clean the under side . I avoid dirt , sand and rocks . That's the job of the string trimmer .

Hopefully that shop won't be in business very long .

I believe that Bad Boy has a elect. operated fuel valve at the carburetor . Those sometimes click when the key is turned to on and off .

???????????????????????????????????????

Have you determined what the fix is ? Thanks

Thanks for the encouragement for the OP . Everyone could use a little of that , even Seniorcitizen.

You make yourself a L shaped Gauge of 3/4 X 1" pine with a strip of styrofoam attached to one edge . Park on a flat surface to heck , not to be confused with level , and the blade will mark the styrofoam . Put a felt tip pen mark on the first if you would like to check deck level .

Load test the battery

On my end It's much better than it was a week ago .

If it still mows grass keep searching for a pre-owned deck while using the one you have . A thought : let it be known at a few mower repair shops you want a pre owned deck in good condition .

Push mower built from 5 different mowers . Long before string trimmers and those weren't needed with this mower . It would suck tall grass / weeds from a fence . The only part new was the blade . The reason it worked so well was the deck was a donut looker , the blade missed the deck edge by...

I believe we better hope neither of those spark test methods are designated for anyone with a heart condition .

Use a paint filter to keep June bugs etc. from ever entering the tank . NAPA auto supplier has those .

Personal experience when i forgot to screw the the stupid dip stick in that by design just sets on the tube to check oil level . In < 5 minutes makes 1 hellofahmess .

I refuse to spend the remaining few years of my life waiting for a site to open .

I had a thought on mine because others doing the same . it idles normal when first started but increase idle speed later . Some piece of that idle system is growing longer as the heat increases . Which could it be .

My X-350 does exactly the same as the . The screw that appears to adjust idle does nothing . It looks as if i'll be looking for a service manual .

I am guessing the problem , when fixed under warranty by their repairman , was never discussed ?

I'll be getting a flap grinder for my Makita .

A 9" Rt angle grinder will sharpen a blade faster than a 4" .

Do you use an abrasive for steel { if there is one for steel } or the one for wood ?

Those using the bench grinder need to dress the stone occasionally to keep it sharp . Those stones that are hardest need to be dressed more often than a softer stone . So why don't we dress the Rt angle grinder . Because of the manufacturing process that dressing isn't needed . It's a...

I use vise grips for some things but not to mechanic . That's why i keep my 6" Ridgid pipe wrench around .

Any mower i buy with a baffle for each blade , those baffles get removed so clippings are dispersed evenly . Attempting to make a mulching deck discharge evenly is a failure .

Date joined really doesn't benefit me , but the date of each post would .

Don't turn around on a dime , enlarge the circle to about silver dollar size until you find a solution .

I've never had the problem but read that sometimes talcum powder or any powder on the belts help until the too tight belts wear some .

is there no axle visible at all ?

Buy a electrostatic roll washable and cut to size . I've used it as a pre-filter for a cheep paper filter for our HVAC unit that was purchased new in 1980 . HVAC techs can't believe that unit is 45 years old but it is . On a mower engine I'd wash -- back flush electrostatic -- after 5 hrs...

Yes if that will reveal the year of manufacture of my John Deere X-350 and where i would find that number on my X-350. We recently moved and i have no clue where the manual is .

For a perfect angle grind with a angle grinder I suggest a home made steady rest you can rest / slide your hands or possibly your arm on .

Where can I find the year of manufacturer on my X 350 ? Thanks for any help .

Trivia for old timers Before synthetics , what material was fly swatter made of .

For those that have and use a bench grinder . https://www.aion-kk.co.jp/en/column/abrasive_03/

I have a couple of non used extra vises setting on the bench . By placing a 2x4 under the rear of the vise in the correct place it gives the angle i want when i hold my Makita grinder level . Sure other measures can be taken to use a mounted vise . Nicks -- that Rt angle grinder makes short...

Chains , install and remove in minutes . The best of both worlds .

No.1 getting gas as it should or not .

It may be worth the extra $1,000 to buy the one with the Kaw .

Modify a Cold chisel to approximately the race radius and drive it out .

Takes some getting accustomed to what order and when sometimes . I'm still trying myself .

You're welcome . Thanks for mentioning this .

Might try a 3 jaw puller if applicable . May locate one at a tool rental if owning isn't wanted .

Cub Cadet IntelliPower 42 in. Gas Riding Lawn Mower, Cub Cadet Engine, Hydrostatic Transmission Has anyone had experience with this engine

This request takes too long to process, it is timed out by the server. If it should not be timed out, please contact administrator of this web site to increase 'Connection Timeout'. _________________________________________________________________ timed it and it takes 5 minutes . I've had bout...