Search results

Th ete is no plate. That’s part of the problem

Here is the mower Fish Here ya go here ya go

Is there a way to delete a thread that you start ?

I understand but this ass was rude. If you don’t know what to ask you don’t ask. I am not a lawn mower professional. I don’t l ow what to ask or what to provide. Some people gave me good information knowing that. Others wanted make themselves feel superior by putting me down. What can I say

I’ll get a pic in a bit. Thanks

But it doesn’t give me model number?

This is all I have. See attached This is all I have. See attached

If I had it I would have posted it. It’s an old one that has been “painted over” I have the engine tag number but not sure if you can cross reference that to a model/year?

I assume the only way to this is through where the battery sits? Do you have a link for the eBay part?

I hope to get up on my lift today to look at it. A couple people have suggested that. Thanks for your input

Thanks!

Is there an area I should try to lubricant?

Yea notice how civil he was?

Exactly what is the center sheave?

Thanks for this. A much nicer reply than I got earlier 😂

Ahhh I thought you were a biker. Apparently your one of those rude MF’ers I see in the forums. I asked a simple question but you didn’t have to exercise your skill at talking down to someone. And your right, I bet your brain IS exhausted. Move on… nothing to see here

I would bet you have a Harley ?

Well I can only hope

I have not tried anything. Im just asking for ideas on what causes these things. Here is a picture of the label On the engine. It just started doing it. I tightened up the brake adjustment.

There is no tag under the seat. I got this second hand or maybe even third .

My MTD mower stopped going into higher speeds. It used to go to all 7. Recently I tightened the brake adjuster nut. Could over tightening it be the problem or should I look elsewhere Jim

Well it is now become a matter of pride. Lol . I’m gonna wait until the mowing season is over and a friend will bring his oxy - acetylene torch over. Plan on heating up then cooling it down a few times . And if that doesn’t work I’m gonna cut that MF off.😂

I did thank you

Well I have 2 bottles of mapped left over but I don’t think it’s hot enough to get the wheel red hot

This guy was funny. I think I know him. So he just put a bolt in the shaft hole and heated the shit out of it and air hammered it off. I don’t have a acetylene torch . But I do have a Mapp. I don’t think Mapp would get it hot enough?

That is the stuff I use on all my rusty stuff once I clean them up. But this wheel is all but impossible. My next step is to pull the tire off and cut the damn wheel off

Duh. Gotta get them off first!😂

I heated it up but not to cherry red. Are you talking about the outside of the wheel or the inside where the hub goes over the axel ? I only have cans a MAPP gas. How long does it take to get it to cherry red? wont it ruin the tire? Quench it with cold water? Won’t that explode in your face ? Lol

Well the holes in my wheels are getting stretched. That’s how tight this wheel is.

The end of my axel has threads where the bolt goes. Someone suggested putting a Allen or hex head bolt in there and using the center of the Allen head. so the jacks need to be on the wheel “sleeve” ( on the inside) or the axel itself. I am so pissed off at this thing I’m about ready to use a...

I’m a little confused as to where you put the point chisel. In the back , driving it towards the front ?

Flat air chisel? Put it on the lip where the rim meets the axel?

I am not sure I can get a good hit in the back without some sort of pipe?

I used to have a 5 pound but it flew off the handle and damn near killed my wife😂😂😂😂

Also most places around here sell 4 pound sledge. Harbour freight has a 5 pound dead blow but it has a soft face

The wheel has the attached type hub. One bolt and a washer hold the wheel on. Your saying to hit the wheel with a 5 pound in the front?

Yes I am hitting it from behind with pipe and a 2 pound hammer.

I hope someone could give me some insight or knowledge on how to get a frozen rear wheel off a garden tractor. Specifically it is a. Old MTD . I have tried everything from PB Blaster to heat to pounding it. Nothing no budge. My next try would be to get an air chisel to the back of it. But I...