Search results

i will check that out...my idler lever seems to move freely, but I have ordered a new spring for it, but the old one is rusty, may affect its tension....the step mechanism attached to the brake pedal arm, it looks like each "speed" should rest on its own "step".. I'm a little confused on how...

yeah 766.the center sheeve of the variable pulley moves freely up and down..and i replaced the bearings also.

I have replaced Variable Pulley bearings.....Variable speed pulley is free, not bound up. Idler pulley is free, not bound up. Upper belt replaced (MTD OEM) , Lower belt replaced (MTD OEM). I am having problems with the speeds on the transmission. It seems it only wants to give me one speed. I...

using fluid film on this deck....now...

check spark when it does that...magnetos breakdown under heat..if no spark until it cools down...replace your magneto.

paint bubbling up...cheap paint and thin decks.....I have seen a john deer a couple of years old losing their paint, garaged or not. MTD products (Troy-bilt) not much better

Well i have to store it outside in very humid florida weather..i keep it covered and keep the top clean but in my experience decks do not last long here no matter what you do. The Deck is 2015 DECK so its actually 8 years old....i've only had it five years myself.

Buying a new deck for my Toro Timecutter 4235 and they are not cheap. I did my best efforts to keep it clean and grass free, and never cut wet grass, but alas, 5 years later, the deck is literally rusting apart. So whats the general consensus on pretreatment before I install the new one. I'm...

at 80.00 plus for a OE cam...I hate replacing something that aint broke...you understand that...but i'm mystified with this one...I've got another in work (a 28N707-0526-A1) doing the same thing, I do not see a bump out of the valves, and it will not revup upon starter application, so its going...

I have a OHV Single cylinder 17.5 B&S engine that exhibited classic signs of camshaft compression release failure...engine would bump 1/4 of a turn on attempting to start. When I opened the engine, the camshaft and compression release device was intact. No visible signs of undue wear on...

sounds like to nme an ignition module breaking down from heat. Thats not uncommon....when it cools down the engine will start,,, then either shut down on its own due to no spark, or when you stop and change a bag or get a drink, it wont restart until the module cools down. Ignition module is...

I think, seat switches works one of two ways...normally open....which means the switch is open and when you get off the seat the switch closes which grounds out the engine ignition to stop it. The other way the switch works is the contacts are closed, and when you leave the seat, the contacts...

Honda Pressure wash engines start up fine, create advertised pressure and then just quit. They will start up again. I have checked the gas caps and they are venting. They will restart but will shut down again within 5 to 6 minutes. Both are doing the same thing. Any thoughts? one is a GX one is...

likely your variable speed pulley is jammed and not sliding

New here but not new to repair of mowers...today I salvaged a crankshaft out of a 9P B&S engine with no compression to donate to a engine with lots of compression but had a bent crank..Never seen one dance like that before! I have a salvage guy who finds them on the street and i repair and...

Well sorry bout that...but i'm fixin to dig into one myself to fix the aforementioned problem on my own mower (a troy bilt Pony) that i paid $50 bucks for...

Likely you've got a bad compression release on your cam. You also have a leakey Carb float not shutting off (or your backfire solenoid is not working on your float bowl, which is supposed to shut off fuel when you turn off your key. You can test that by turn the key on, you should be able to...

hoses...and i've checked for fuel flow...the hoses are clear and free flowing.

i have two pressure washers with GCV-160 engines. They both pump fine, when the engines running. They both start up easily,run for a while then just shut off. I've drain tanks and checked for fuel flow. I have checked the caps to ensure the gas cap vents are clear. The carburators have been...

Selling. $150 plus shipping. I have this listed on Ebay also and Facebook Market place.. good operating condition 6 speed. with pulley