Search results

But don't you just want to know why it stopped working? :-) Yes, it's more for the challenge. And the sense of accomplishment when I get it done. It's a nice break from my very stressful day job. I've been fiddling with it since at least May. I started by replacing the carb, thinking that's...

I've now got both wheels and wheel assemblies off and the axle does spin freely. The axle looks to be pretty clean and free from rust or pits that would cause it to bind in the wheel bushing. I've also removed and inspected the belt and it doesn't appear to be dried out or cracked or shiny. I do...

I'm reluctant to get involved with trying to rebuild the transmission until/unless I can be sure. Is there any alternative at this point? Does it really sound like the transmission is the problem here? How can I test it before taking it apart?

Hi, I have an HRR216 S3DA MZCG-6078970 basic lawn mower that I picked up at the curb. After getting it to start again, I realized that it doesn't roll back on its own and doesn't go forward under load when the self-propel system is engaged. I've followed a few videos demonstrating how to take...

Thanks again for your help. The throttle assembly didn't appear to be bent in any way, so I wanted to avoid bending it, unless it was absolutely necessary. Turns out I was able to simply adjust the throttle cable by just loosening the Phillips screw, sliding the cable down a bit, then...

I think I know what you're talking about. The picture here is from when the throttle is fully ON. The choke should be in the closed position but it is not. You are right that it doesn't appear to go up far enough to fully close the choke. The arrows in red are part of the assembly that connects...

Thanks so much for your help. It is fully open with the throttle in the fully on position. I believe it should be closed, to allow a greater concentration of gas to get it started, correct?

Given how difficult it is to replace the carb again, is there any way to make adjustments on it once it's installed? Do you think it's possible it just needs to be adjusted? Could it be related to the air/fuel mixture screw?

Just now seeing your update. This is the carb I purchased. Are you able to tell me if this is suitable? https://www.amazon.com/gp/product/B0769TD8TD/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

Thanks so much for your help. Model: HRR216 S3DA 21" Ser: MZCO 6078970

Hi, I have a Honda HRR216 that I picked up off the street and trying to get running again. I replaced the carb, and it starts with a bit of starter fluid, but not on its own. There's no primer bulb. Are there other adjustments I'm missing? Any advice would be greatly appreciated.

Thank you - I'll order a new one.

Hi, yes, I should have been more clear. It looks to be fixed. The tension doesn't look to be adjustable. There's also already quite a bit of travel with the cable that I feel like it should be engaged fully.

Hi, I have a Honda HRR216 S3DA 21" that I picked up at the curb. I replaced the carb and it's now running great. However, the mower won't move. If I lift the back wheels above the ground, they do spin when the self-propelled bar is engaged, but not enough power to go forward on its own. I took...

Hi - no one has any tips or advice to offer about what I possibly could be doing wrong? Anything I should watch out for when replacing the carb or trying to get it to start?

Hi, here is the carb I purchased and replaced https://www.amazon.com/dp/B0769TD8TD

Hi, I picked up this Honda at the curb probably more than a year ago and finally now trying to get it to start. It runs for a bit with some starter fluid sprayed directly into the carb, but then dies. I replaced the carb, but still the same thing. It's possible I did something wrong (there's a...

The fix was to replace the carb again.

Okay, I worked on this further, and figured out the primer bulb problem. I took it apart completely, cleaned it out, and made sure the little hole lined up with hole in the carb. Now I know. However, the problem now is that it runs rough. It won't stay running on its own because the choke is...

okay, understood now - I was referring to the throttle plate (or choke valve, apparently). Do you have a recommendation on either the proper carb to get or a better place to get it? It looks like the primer bulb is not injecting fuel into the carb. How do I troubleshoot this? The bulb doesn't...

If you've been following along with my previous thread, I'm having some issues getting a Toro 124T02 started. It's a curb find from about two years ago that I'm finally trying to get running again. I replaced the carb then, but it may have been the wrong one, although I do recall it did work at...

This is the parts manual for the Toro 124T02. I don't see any references to a governor or missing parts. I'm thinking it's the autochoke that ILENGINE mentioned above. Any further ideas greatly apprecaited...

I found this number stamped on the shroud covering the muffler: 124T02-0161-B1 07081657 Here's a picture of the whole mower

Thanks so much for your help. This is the info I have on the engine, as anything that once appeared on the mower body is now gone. I also didn't see any screws or nuts to remove the bowl. Family: 7BSXS.1901VH 277307 This is the carb I bought for it: https://www.amazon.com/gp/product/B07C2YWN51/

Hi, I picked up a Toro 22" Recycler from the curb last year. I replaced the carb and I believe it ran fine, although I never used it. Now I can get it to start by spraying some starting fluid into the carb, but it dies shortly thereafter. I'm confident the carb is getting fuel, as I disconnected...