Search results

Results 1 to 20 of 20
  1. L

    Alternative Carburetor With High And Low Adjustment

    I am searching for a carburetor to replace this with a high and low adjustment. It has a 15mm venturi and the displacement for the bolt up holes are 32.23 mm center to center. Thanks
  2. L

    Can Not Find Parts For Husqvarna 125BT

    Thanks I have never seen or used this acronym before.
  3. L

    Can Not Find Parts For Husqvarna 125BT

    What does NLA mean?
  4. L

    Can Not Find Parts For Husqvarna 125BT

    I have tried multiple websites and I can not find any parts for this blower. Is there a different way to search for parts? Is there a newer blower with different part numbers I can use? This is what I am searching for. Husqvarna 531009639 GASKET, Husqvarna 531009640 GASKET, Husqvarna...
  5. L

    Odd Looking top for the low and High Carburetor Adjustments

    When I look up eccentric screwdriver I see different heads. Some make sense while others do not. Why is this? For instance "ETA 7750 Eccentric Screw Screwdriver 1.40 ** Swiss Made **" https://www.ebay.com/itm/ETA-7750-Eccentric-Screw-Screwdriver-1-40-Swiss-Made-/264561963223
  6. L

    Odd Looking top for the low and High Carburetor Adjustments

    I have that set minus the Eccentric screwdriver. Looks like I spelled it incorrectly in the original post.
  7. L

    Odd Looking top for the low and High Carburetor Adjustments

    Alas I shall haveth my way with this equipment that I own. I sweareth upon this rock I stand, I shall save it from waste and save my hardware for another day.
  8. L

    Odd Looking top for the low and High Carburetor Adjustments

    I have a Craftsman GAS TRIMMER Model No. 316.791810 Incredi-Pull and it has a very odd looking top for the low and high carburetor adjustments. What tool is used to adjust these? From searching it looks like a Ecceotrix screwdriver. If it is a Ecceotrix screwdriver, where can I purchase...
  9. L

    Taper Fit Flywheel Loose, Weed Eater BC24W

    Thanks you were correct "more precisely the threaded clutch that holds the flywheel against the taper. " It all works well now.
  10. L

    Parts For Homelite UT-20769 Trimmer

    They try to make it all so difficult for anyone to repair.
  11. L

    Parts For Homelite UT-20769 Trimmer

    Thanks dougand3 and bertsmobile1 for the help. I emailed 4 local shops to see if they have parts. I await a response. I have noticed in the past that they have model numbers for parts from newer trimmers that do match. What I have always wanted to know is. Is there a resource where I can...
  12. L

    Parts For Homelite UT-20769 Trimmer

    I am having some difficulty finding parts for this trimmer. This is my issue. I can find them at various sources. Does anyone have a source that might have most of the part so I can minimize on shipping cost? These are the part numbers. 98766A GASKET-Carburetor 06900A GASKET-Heat Dam...
  13. L

    Taper Fit Flywheel Loose, Weed Eater BC24W

    "Nut or bolt whatever holds the flywheel on" has no direct bolt or nut holding it on. What StarTech described is how it is assembled. "You get them to lock by applying a lot of force SLOWLY" I tried this with no success. "Steel wool , scotchbrite 1000 grit wet N dry whatever you have soft...
  14. L

    Taper Fit Flywheel Loose, Weed Eater BC24W

    I will pull it apart and do a nice cleaning. What do you suggest to use to clean this? The key is definitely apart of the flywheel and still there not damaged. What bolt are we talking about?
  15. L

    Taper Fit Flywheel Loose, Weed Eater BC24W

    The key is not damaged. I did place it all back together. I need to poke at it to see how well it stay through the shroud. The washer, spacer, (drive coupler), clutch, and clutch housing are back together. The pull the pull start and the spark is generated. I am concern because of the...
  16. L

    Taper Fit Flywheel Loose, Weed Eater BC24W

    Taper Fit Flywheel Loose The crankshaft on my Weed Eater BC24W has a taper that I squeeze the flywheel onto. I separated the two when I was rebuilding the engine. When I tried to place them back together they will not stay pressed together. I tried hammering it on and also pressing it on...
  17. L

    WYL Carburetor Adjustments

    This is fixed. I had to widen the passage for the fuel via the main jet by using a very small drill bit and a pen vise to hold the drill bit and open the hole a little. It works fine, blows well and does not fall on its face. It was an easy repair once I knew what to do. Hope this help...
  18. L

    WYL Carburetor Adjustments

    I did a pressure test and the carburetor holds pressure from the primer bulb and the fuel intake side. In this photo https://www.lawnmowerforum.com/threads/wyl-carburetor-adjustments.57889/#lg=post-349810&slide=1 Is this bronze looking recessed thing what I can screw in or out to adjust the...
  19. L

    WYL Carburetor Adjustments

    "If you used carb cleaner to blow through all of the orrifaces then better than average chance you have buggered up the check valve." this is what I did. Is there a carb that fits this that is adjustable?
  20. L

    WYL Carburetor Adjustments

    I have the following carburetor WYL. It is from a Troy-Bilt backpack blower. I can not find where the carburetor adjustments are for high and low. It seems the closes is the adjuster screw for idle. I rebuilt the carb and it idles but when I press the gas it cuts off. I need to adjust the...
Top