Menu
Home
Today's Posts
Unread Posts
Trending
Search forums
Members
Current visitors
New profile posts
Search profile posts
Top Posters of the Month
Mowers
Repair
Buying Advice
Operation
Pro Talk
Photos
New media
New comments
Search media
New
New posts
New media
New media comments
New profile posts
Latest activity
Log in
Register
What's new
Search
Search
Search titles only
Latest activity
Register
Menu
Log in
Register
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
slomo's latest activity
S
slomo
replied to the thread
Craftman 5000 Watt Generator hard Starting when Hot
.
10w-30 will shear down awful fast in an air cooled engine. Briggs, Kawisaki, Kohler and so on state multi-grade oils will be consumed...
Aug 26, 2025
S
slomo
replied to the thread
15 amp fuse blows
.
Moisture inside the grass crossing terminals. Good find........
Aug 25, 2025
S
slomo
reacted to
rich0587's post
in the thread
15 amp fuse blows
with
Like
.
Update time, I was looking thru the circuit again. Noticed that there was a buildup of dirt/grass on the connector to the key switch...
Aug 25, 2025
S
slomo
replied to the thread
John Deere X360 Backfire and no run.
.
Carb needle sticking open. Clean or replace needle and seat. Please describe this testing procedure. What is fine about it? Cease...
Aug 25, 2025
S
slomo
reacted to
ACF's post
in the thread
kohler carburetor problem
with
Like
.
replaced carb and key switch
Aug 25, 2025
S
slomo
replied to the thread
E140 bogs under load
.
That is a-maz-in'. Bet if you cleaned the old ones and measured the internal resistor if it had one, would of worked. Gap could of been...
Aug 25, 2025
S
slomo
reacted to
Jack9's post
in the thread
Fuel filter suggestion?
with
Like
.
Thanks again. I had no clue. You're the only person that I've ever seen mention that type. For anyone else wondering, this shows removal:
Aug 25, 2025
S
slomo
reacted to
Davenj4f's post
in the thread
Spindle failure
with
Like
.
Update: Last week I removed the relief fittings (spring loaded weep hole plugs) and installed standard plugs. After 3 days of light...
Aug 25, 2025
S
slomo
reacted to
jimvw57's post
in the thread
RZ4619 control arms
with
Like
.
I guess I didn't update this... I installed the replacement arm parts, after re-ordering the correct one, (use serial number to get the...
Aug 25, 2025
S
slomo
replied to the thread
Loping engine
.
Did you get this thing running? Never heard back.
Aug 15, 2025
S
slomo
replied to the thread
Gas tank removal
.
And not one visible screw or screw hole. Your FIRED!! My best lame Trump joke. LOL
Aug 15, 2025
S
slomo
replied to the thread
Best Practices for Maintaining a Healthy Lawn
.
What is the grass type? Cool and warm season turfs have a different recipe for maintenance.
Aug 15, 2025
S
slomo
reacted to
Tiger Small Engine's post
in the thread
Spindle Bearings
with
Like
.
We are talking about the cost difference of a few bucks a tube of regular cheap grease versus better quality red and tacky grease. I...
Aug 15, 2025
S
slomo
reacted to
ILENGINE's post
in the thread
Spindle Bearings
with
Like
.
I have seen several cases of grease failure over the years. A couple of those cases was Valvoline synthetic wheel bearing grease. Your...
Aug 15, 2025
S
slomo
replied to the thread
broken shroud on underside of deck
.
Good point.
Aug 14, 2025
Top