Recent content by SHB

  1. S

    Blades for Exmark Radius E

    I use low loft blades, get them from an eBay seller propartsplace, part number EXMARK 103-6388. Low loft blades use less fuel in heavy grass, but aren’t good for bagging.
  2. S

    FS56 RC puzzle

    On morning my FS56 RC weed eater started fine, but would bog down when attempting to throttle up, was fine the evening before. So I assumed that the high speed jet was clogged or maybe the spark arrestor. Dismantled the carburetor, inspected, removed the high speed jet, ran carb cleaner through...
  3. S

    Belt & idler question

    Turns out the bolt holding the pulley had backed off. Added some loctite & tightened, concerned with over tightening a bolt going into cast aluminum with no threaded insert. A week later the ⅜” bolt holding the assembly broke off, repaired yesterday, getting the idler springer back on was no fun.
  4. S

    Belt & idler question

    Have a 4 year old eXmark radius, 60” deck. First deck belt lasted about 400 hours. Got a replacement at Rural King (dealer wasn’t open), it ran about 8 hours then disintegrated. Got a replacement from the local dealer, have run it about 8 hours, just came loose. I checked the deck pulleys, they...
  5. S

    Best for hills?

    I mow about 10 acres that contains some significant slopes. Started with a lawn tractor (it was a craftsman), never had an issue, but the high CG definitely caused a pucker factor that limited the slopes I was comfortable to attack. Next was a 60” badboy ZTR with lugged tires, much better, the...
  6. S

    battery worthless

    Some chargers need to see a minimum voltage across the terminals to turn on, this is to protect the charger in case the leads are shorted. Thus they won’t turn on and charge if the battery is totally dead. I trick the circuit by connecting the charger to the dead battery, then momentarily jump...
  7. S

    Z254F Pump/ drive belt

    Thanks! On my badboy ZTR there is a removable plate, which exposes the belt, easy to get to. Of course, it also shreds the fans on the drives when the belt goes.
  8. S

    Z254F Pump/ drive belt

    Neighbor has a one year old Husqvarna Z254F zero turn mower. Pump belt came off today, I can’t find a belt routing decal on the machine and the manual barely mentions it. Anyone have a diagram showing how this belt runs? I tried putting it back on for her, but it’s on the wrong side of the idler...
  9. S

    Ferris 500s or Bad Boy Maverick, which is best for my farm?

    I have an older bad boy, Koehler engine, 60” deck. Got it at auction, was about 11 years old when I bought it. Built like a tank, I have abused it mercilessly clearing brush & briars on our place. Put lugged tires on it to better handle slopes. Only negative has been documentation, the manual &...
  10. S

    Stihl love/hate MS251C

    I have one, it’s always been easy to start. Just followed the procedure listed above Push the primer a couple of times Hold the throttle wide open and advance the control to the start position Pull the cord gently a couple times till it “burps” Move the control up one notch Pull cord, generally...
  11. S

    Stihl love/hate MS251C

  12. S

    Radius vibration

    Thanks - hadn’t thought about that! Will try putting my spare belt on if the vibration persists with no blades on the machine (see below).
  13. S

    Radius vibration

    Good idea on running W/O blades! I presume you meant on blade at a time to isolate where the problem is. I don’t have a balance machine per-se, just balance them on a screwdriver shaft, if they sit level and don’t try to turn I consider them good. However, the first step I took was putting my...
  14. S

    Radius vibration

    It appears that the spindles mount via bolts from the top into bosses cast into the spindle housing. Top of deck is clean, appears to have reinforcing plates where the spindles bolt up, no sign of cracks.
  15. S

    Radius vibration

    Jacked the mower up today, scraped away the crud, couldn’t find any signs of damage. Think I will run it for a couple of hours, then look again. Thanks for your thoughts!
Back
Top