Recent content by Hayward51

  1. H

    Scag Ignition Relay

    It's not the cost of fuses that worries me. IF I can get the 12V to stay on long enough to find the wire, what do I do with the 12V wire ? Ground it ?
  2. H

    Scag Ignition Relay

    Star Tech, if I knew more about the gounding system, I would continue myself and not bother you any further. I'm at a loss not knowing and would like to know how to test for the 12V without blowing fuses. I do appreciate your input.
  3. H

    Scag Ignition Relay

    I was trying to figure it out myself but I still don't understand how the grounding system works. I toned the Pink wire just to make sure it was going to the parking brake. The tone wouldn't run on the grounded wire until I released the brake. I assumed a wire past that switch had it grounded. I...
  4. H

    Scag Ignition Relay

    When I got to the part about grounding the red wire at the seat switch is when I noticed I had 2 red wires. That part was most confusing of all. How does that switch work if disconnected ? And is it necessary after disconnecting module ? I disconnected the interlock module turned key ON, blew...
  5. H

    Scag Ignition Relay

    Star Tech, I got my seat switch in and started my rewiring of the Scag. I read thoroughly and when I got to the seat switch part, I found I have 2 RED wires and a BROWN wire going to the switch. One red goes to hour meter and one red goes to the PTO switch. I had 12V on one of those red wires...
  6. H

    Scag Ignition Relay

    I'm sorry to seem too dense to comprehend your reply but, "means you do not (x) to be applying (x) to the ignition coil kill terminal", sounds like a word or two are missing in this statement.
  7. H

    Scag Ignition Relay

    Star Tech, One major question on my mind (yes, it's confusing), when you say "don't do this unless the circuit is converted to a grounding", what exactly determines that the circuit is grounding ? I'm assuming it's the rewiring of the PTO switch. ?? I just want to have this part straight in my...
  8. H

    Scag Ignition Relay

    I have ordered the seat switch with bracket. I won't expect it within a week (hopefully sooner) but I most probably will be back here with questions and to let you know how it works out. Thank you for your input, Star Tech.
  9. H

    Scag Ignition Relay

    Thank you for those instructions. I will study the wiring to familiarize myself thoroughly before snipping. BTW, the PO also removed the seat switch and connected the wires together. I'll have to replace the switch and plug.
  10. H

    Scag Ignition Relay

    I have verified that all safety switches are good. Looking at the diagram for a 5 pole relay, it shows that the terminal the green/black wire attached to is (or should be) grounded. I have the relay grounded. All this is very confusing to me but I would like to get the safety features working.
  11. H

    Scag Ignition Relay

  12. H

    Scag Ignition Relay

    Thanks for your reply. I have this diagram. Not the switch make/break table. All seems to be wired correctly with Green wire from switch to relay HOT when key to start. I don't understand how it gets to the Green/White (stripe) wire going to the engine harness. If I ground Green/Black (stripe)...
  13. H

    Scag Ignition Relay

    This is 2002 Tiger Cub STC 48A 20CV s# 7640064. I had to dig for the wiring diagrams I have. The manual diagram isn't much help.
  14. H

    Scag Ignition Relay

    Hey Folks, I'm back to working on my Tiger Cub I rebuilt last summer. I posted questions in September about rewiring because of PO rigged the wired and did away with all safety switches. I'm still trying to figure out how the safeties all work through the harness. Today's question is ...does...
  15. H

    Scag Disc Brake Pads

    Thanks for your replies. I considered riveting myself but I noticed it wasn't common rivets.
Top