Recent content by dkamp

  1. D

    Plastic Trans

    Looking for a similar mower sounds like a good idea. I had hoped to not need to replace my Bags and grass Shute. I will start watching Craigslist and Market place. But If I don't find one by spring I may just look for a good prybar to get my wallet open enough for a new rider. But this spring...
  2. D

    Plastic Trans

    Tiger, the place with the other mowers is an Auto Salvage yard where people sold their old mower for scrap price. Eventually the Auto Salvage yard will call for a pickup of all the scrap they bought, to sell to the big guys who work the big loads. Its in Terre Haute, Indiana. I've looked the...
  3. D

    Plastic Trans

    I have a Craftsman 917.203900 sometimes refered to a T3000. It has a Plastic Trans that is always having issues. its a General Transmission RS800 SD-P. Should I simply scrap it? Should I get another Trans that fits? How can I know what would fit? THere is a salvage yard that has 30-40 riders...
  4. D

    RS-800 Adjustments

    How would I know if bypass mode stays working? is there a test that can be done?
  5. D

    RS-800 Adjustments

    I was able to tighten the nut on the inversion rod a few turns and it was better, so I tightened it a total of about 1/8" shorter and it does work a lot better. Not as well as I think it should, but well enough until I can remove the deck again. Is that the primary fix for a weak reverse on a...
  6. D

    RS-800 Adjustments

    Thank you for the response. I do have a copy of the Service Manual that was downloaded from GT. (39008-D, Apr 2019) Is the adjustment you are referring to called the Inversion Rod? On page 19 it only mentions to have the length to 2.5 +-0.01 Inches. I'm assuming also to make sure the lever is...
  7. D

    RS-800 Adjustments

    I have a Craftsman 917.203900 After replacing the RS-800 P Variation kit, all seems OK except.... When I press the Reverse, it does reverse very slowly, it I hook my heal on the Go lever and pull it up (Which is similar the pressing reverse harder/more) it reverses ok. It seems like there is an...
  8. D

    Blower Purchase decision

    I also noticed that none of the Premix fuels state that the Oil is Synthetic. So is Premix off the menu?
  9. D

    Blower Purchase decision

    I ended up buying Stihl BG56 C-E There are two kinds of Stihl oil a Orange bottle and Silver. The Sales guy told me to use the Silver since it was Synthetic, and the Orange was not. Is it sales talk or true to only use Synthetic? (The Owners Manual does say to use Synthetic Oil) Should I Always...
  10. D

    Blower Purchase decision

    I decided to buy a Leaf Blower. I'm looking for opinions. When I look at name brands, they seem pretty expensive. local dealers are all over the place and claim their brand is the best. On AZ, I see a lot under $100 but with Brands that are odd names. My primary question is should I overextend...
  11. D

    Automatic Compression Release

    it is working well after the valve adjustment. I also found why it was surging while giving it some needed attention. I noticed that where the carb attaches to the Plastic Intake manifold, there was a gap from the plastic being warped. I little Gasket maker sealed it until I get another intake...
  12. D

    Echo SRM-225 seems tired.

    Craftsman Garage: I replaced the Carb with an Amazon version and new fuel lines and filter. StarTech: The SRM-225 Serial number is S03912303806 If I get the Max RPM how can I test or check that? I would also assume it is with the string being a particular length? This has 4 strings hanging out.
  13. D

    Echo SRM-225 seems tired.

    I was given an Echo SRM-225. It would not start. I cleaned the carb and replaced plug. It runs but seems sluggish and underpowered. Can anyone suggest a list of things to check? I did check the exhaust spark arrester, and it is clean. Should I remove the Head and check the rings? if so what do I...
  14. D

    Automatic Compression Release

    Hey Craftsman Garage, thank you for your information. Yesterday I did buy a new 320 CCA Battery and cleaned all connections on Battery and Starter. I had to wait for my Gasket maker stuff 24 hrs to dry after sealing the Valve covers. I will test how it cranks today. Another subject.. I do have a...
  15. D

    Automatic Compression Release

    I do see a Mfr date of Jan 2014 on the engine, if that helps nail down if I actually have ACR or not. Should I go thru the trouble to add the newer Cam with the ACR? or live with the occasional Roll the engine manually to get over the compression stroke so it has momentum to spin and start up?
Back
Top