Menu
Home
Today's Posts
Unread Posts
Trending
Search forums
Members
Current visitors
New profile posts
Search profile posts
Top Posters of the Month
Mowers
Repair
Buying Advice
Operation
Pro Talk
Photos
New media
New comments
Search media
New
New posts
New media
New media comments
New profile posts
Latest activity
Log in
Register
What's new
Search
Search
Search titles only
Latest activity
Register
Menu
Log in
Register
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Davenj4f's latest activity
D
Davenj4f
replied to the thread
Spindle failure
.
Update: Last week I removed the relief fittings (spring loaded weep hole plugs) and installed standard plugs. After 3 days of light...
Aug 23, 2025
D
Davenj4f
replied to the thread
Spindle failure
.
Can't deal with the internal spacer till I tear one down again. Meanwhile, I'm going to use a plug in the weep hole and see if that is...
Aug 14, 2025
D
Davenj4f
replied to the thread
Spindle failure
.
OK I follow. You are letting the top bearing be able to move up as needed. But the trash shield is pressed in over the bearing. There...
Aug 12, 2025
D
Davenj4f
replied to the thread
Spindle failure
.
I have to use the shop press to push everything in place. About the weep hole. I took the weep hole relief fitting off and was...
Aug 12, 2025
D
Davenj4f
replied to the thread
Spindle failure
.
I think I understand what you are saying. I'll check that measurement next time I have one apart. But I think the bearings are tight...
Aug 11, 2025
D
Davenj4f
replied to the thread
Spindle failure
.
Not sure what you mean by pushing the outer race with fingers. I use my shop press to disassemble and reassemble. Attached is the...
Aug 11, 2025
D
Davenj4f
replied to the thread
Spindle failure
.
Yes. Notches at either end.
Aug 10, 2025
D
Davenj4f
replied to the thread
Spindle failure
.
Decided to go with Schaeffer Green Extreme Pressure Waterproof Grease NLGI #2. Good for high temps also. Thanks for replies. Will...
Aug 9, 2025
D
Davenj4f
replied to the thread
Spindle failure
.
I see a bunch on Amazon. Any particular brand to go for, or stay away from ? Or doesn't matter, long as it's hi temp disc brake bearing...
Aug 8, 2025
D
Davenj4f
replied to the thread
Spindle failure
.
I like that thought. I will do next time I have them off. Or feel real industrious and not tired !! I hadn't thought of that, thanks.
Aug 8, 2025
D
Davenj4f
replied to the thread
Spindle failure
.
Forgot to add, it's usually the bottom bearing that goes bad.
Aug 8, 2025
D
Davenj4f
replied to the thread
Spindle failure
.
The spindles already have a weep plug at the bottom. After two days of mowing, i can pump 10-15 times to fill back up with grease. I...
Aug 8, 2025
D
Davenj4f
replied to the thread
Spindle failure
.
Good morning. The spindle would rattle, be loose. I could feel the roughness in the deck lift pedal. After disassembling, the bearing...
Aug 7, 2025
D
Davenj4f
replied to the thread
Spindle failure
.
Thanks for the reply. You are correct about 3rd party replacements. Never had much luck with any of them. When I bought all new...
Aug 4, 2025
D
Davenj4f
posted the thread
Spindle failure
in
Ferris
.
ISX2200, 52", FT730V EFI I keep having to replace or rebuild my spindles. I can rebuild them in my sleep I think. I do some heavy duty...
Aug 4, 2025
Top