Menu
Home
Today's Posts
Unread Posts
Trending
Search forums
Members
Current visitors
New profile posts
Search profile posts
Top Posters of the Month
Mowers
Repair
Buying Advice
Operation
Pro Talk
Photos
New media
New comments
Search media
New
New posts
New media
New media comments
New profile posts
Latest activity
Log in
Register
What's new
Search
Search
Search titles only
Latest activity
Register
Menu
Log in
Register
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
closecut's latest activity
C
closecut
replied to the thread
Craftsman T2400 Kohler won't start
.
The new fuel anti;knock compounds in gas foul a plug very easily,and is almost impossible to remove the fouling by normal means,wire...
Saturday at 11:59 AM
C
closecut
replied to the thread
Craftsman T2400 Kohler won't start
.
Try this:Open the throttle wide open.Crank over engine and see if raw fuel comes out of spark plug hole.If not there is definitely a...
Saturday at 8:11 AM
C
closecut
replied to the thread
Issues with pto (solved)
.
The proof is in the pudding as they say.No repeat failures with the 1n4007.When I was 10 years old,I was building cat whisker...
Apr 7, 2024
C
closecut
replied to the thread
Issues with pto (solved)
.
That is not what I am saying.Read my reply carefully.The flyback(reverse voltage) is the most important in this case. The spike can...
Apr 7, 2024
C
closecut
replied to the thread
Issues with pto (solved)
.
The 700 volts is the maximum constant supply voltage that it can handle. The PRV is the reverse voltage it can handle.The reverse spike...
Apr 7, 2024
C
closecut
replied to the thread
Issues with pto (solved)
.
1N400X Diode Reverse Voltage 1N4001 50 V 1N4002 100 V 1N4003 200 V 1N4004 400 V 1N4005 600 V 1N4006 800 V 1N4007 1000 V
Apr 7, 2024
C
closecut
replied to the thread
Issues with pto (solved)
.
Apr 7, 2024
C
closecut
replied to the thread
Issues with pto (solved)
.
Yes.The diode I recommend is better than the oem. The oem is the minimum to do the job, and the cheapest.It also allows them to sell...
Apr 6, 2024
C
closecut
replied to the thread
Issues with pto (solved)
.
A 1N4007 diode will wok just fine.It has a 1000volt peak reverse voltage.Here is a link to diodes on Amazon.Cheap as dirt.The negative...
Apr 6, 2024
C
closecut
replied to the thread
I think someone is in trouble...
.
That is called "Pencil Whipped Maintenance" where the check list is checked off without actually doing the work.No second chances on...
Mar 9, 2024
C
closecut
replied to the thread
Blade-balance oddity
.
Is the hole in the blade round,or star or other shape?If not round,and perfectly centered your results will not be good.Use a level to...
Mar 9, 2024
C
closecut
replied to the thread
Craftsman deck exploding
.
A mower was brought to the shop with same problem.The belt was routed wrong.The flat side of the belt was rubbing against a guide.The...
Feb 24, 2024
C
closecut
replied to the thread
Run at Full Throttle? Pt 2
.
Most engines are designed with a certain rpm for max efficiency and durability.Fans and pumps do not respond in a linear manner.Double...
Feb 24, 2024
C
closecut
replied to the thread
T210 blade removal
.
Purchase a nut-cutter from amazon.It will cut off nuts without damaging the threads.Saves a lot of time and trouble on otherwise stuck...
Feb 24, 2024
C
closecut
replied to the thread
Head gasket
.
No firing order found?Here is an old school method to get the tightening sequence right: Start in the center and tighten in a expanding...
Feb 24, 2024
Top