Search results

Messed up my 17.5 Kolher Command messing with the Governor. Ran just fine before messing with it. What is the correct way to set it back? I’ve tried holding throttle wide open and turning shaft counter clockwise and still just wide open rpms. Any help would be greatly appreciated..Need to mow!

Cleaned carb and reinstalled on motor. Only wants to run on choke and also surges with and without choke. Carb still dirty? Plugs have spark. New fuel filter and fuel making it to carb. I’m lost. And for the life of me can’t find a carb for that motor anywhere! Jacks small engine said they don’t...

Looking to gettin this thing running. From bottomed out where do I need to put my High Low and LA screws for it run decent? Thanks

Ordered the Wrong R.H. deck lift rod way to long. Anyone have a part number or lead me in the right direction for right part? Thanks in advance

Mowing fine one day then just died! New battery, solenoid, key switch, pto switch, rectifier, Fuse replaced and lights up when key is turned on but no dash lights hour meter headlights or anything when turn key. ?????? Please help...looked and followed all wires and looked good no frays or...

Just acquired a hydrostat 21hp 22hp 48” deck Gardenway by Troy-Bilt. Lookin for a model number on these as it don’t have a seat. Needing to order deck belt. Thanks I’m advance

In search of a front tire for my John Deere 210 16x6.50x8 willing to buy if anyone got a decent one laying around. Also a starter for a k241 10hp. Let me know. Thanks

I need to put my brushes and cap back on armature!! How in the heck y’all accomplish this having to hold all 4 spring loaded brushes. Special tools? Tricks? Tips? I’m about to buy a new starter. Thanks in advance

Needin tricks and tips to keep brushes pressed in on springs to attach back on armature of starter. And Go!

Lookin for a manual online on how to put the mower deck back on this snapper front Engine mower. Also part number for idler spring. Thanks

Looking for the plastic choke knob that will fit above chainsaw. My prior choke knob cracked and broke off. Any suggestions or alternate part to fit this saw for a choke knob be appreciated.

I've got a Lawnboy insight I believe 4cycle with the BCS engage. All of a sudden when I go to engage the blade it kills the mower. Mower runs perfect but mashing the bcs switch kills it unless I let off of switch the goes back to idle. Any help be appreciated it's a good mower. Thanks

The easiest possible way to replace fuel lines in tank! Got to get the hose through two holes and the 2nd you can't see!! Bout ready to rip my hair out! Any easy tips tricks let me know please. Lol. Pain in the a**

Havin a heck of Time setting the adjustments on carb for it to start. Idle/Air H, L settings. What would be good preset to get this to start. I'm at a loss and need this running

I've got a Lawn boy 10687 push mower that has stumped me. Equipped with BCS (Blade control system) As I push the handle to engauge Blade it wants to die instead of starting blade. Mower runs great other then that. Any ideas? I'm at a loss

Can't seem to pull off air filter cover so I can take carb off to clean it. Out of ideas. It's loose just won't come off!

I've got a lawn boy 10687 Sesa speed runs fine. When engauge BCS for blade mower dies. Relay checks out good. Looking for a diagram for drive transmission as I've got a spring that was somewhere hooked up to it. Thinkin that may have something to do with it. Any help be appreciated. pics below

Drive belt was already off and gone when I got the mower. Needing advice on part number of drive belt. Diagram of routing and any help on how to install it. Thanks in advance! Dan

Model # 136M675G192 New battery, solonoid 12.7 volts off charger cranks over then dies battery now 12.3 or lower volts. What would be causing this? bad stator? What's a easy way to test this? Mower is currently dead. Thanks in advance.

CRAFTSMAN ZTR with 20hp courage wanting to replace with command only question I got is the courage exhaust is mounted on (R) top rear of engine as this command exhaust is on the bottom front. Is that going to be a problem? And what other issues could I run into? Wiring etc?

Mower deck would not disengage blades while disengaged. Replaced deck brakes and deck belt. Seemed to work but will running idle for couple minutes you can see the deck pulleys slightly starting to spin while disengaged. And then smoke and burnt rubber smell from the pto shaft pulley area? Also...