when i pull yhe mower backwards the wheels won;t move. some one told me there is a spring
that controls that, but i can;t see anywhere a spring goes, is there a diagram of it anywhere,
i have a briggs 461707-0143-E1 and i took the carb off to clean it and now i can;t see how to put back on.
can somebody tell me where to get a good picture of the linkage setup..
i looked at the diagrams but they don't show where to hook up the black throtle plate on the carb.
i have a JX75 self propelled mower and i can;t pull it backwards, does the pinion gear on each wheel have to be on the excat wheel
or the interchangable. i think there is a right and left on them but they are so worn i can hardley make out anything.
the number is 1691537 mdl.
serial is 5789
got this mower for free, and its in picies.
yhe diagrams i found are not very good, on the deck there is a long bar that goes from the brake on the deck but i can;t
see where it goes on the mower. and the up and down adjustment dosen;t work.
WHERE can i...
somebody brought in, we work on small projects, oil changes ,service, said it was sitting for about 3 years.dont know if it ever ran,tried to purge trans, but nothing .
all belts are on, checked the wheels keys are in.it is a rhdro trans, the book says its sealed from factory, no where to put any in,
the levers are moving.every thing is moving like it should just wont move under power.
starts and runs fine, but wen i hit the forward or reverse it won't move. the freewheel lever is all the way in, but it dosent make any difference if its in or out it freewheels
eather way.could the trans be shot. i dont know any more i can do.
have a 12 horse vert briggs, and i can[t get it to charge battery, tried a new stator hooked it up to the hot side of the battery, and it still won;t charge.
could i have gotten a bad stator, how do you check them to see if they are working/
i have a tory wheel horse, the wiring burnt up, and i want to rewire it, can sombody send me a drawing,
simple wiring of just the starter coil and solenooid to switch, no safty switches.
i have a toro rear engine mower, and it won;t do anything by turning the key, i can pull the wire off the coil and jump it direct to the starter.and it will run,
or i can jump the solinoid and it will start but not the the key. could it be the solinoid or some thing in the wiring.
can you repair a ball joint on a lt180 mower
the steering ball joint keeps popping out. i have it taped on now but is there any way i can fix it,
they want 30.00 fo a new one.
I have a john deere tractor with a leaf vac on it and the motor is blown,
5 hp kawasaki fa2100
all it has on it is powerpack fa2100.
i looked for another motor but i can;t find anything on it.
the motor is on the leaf vac.
any body know where i can get one.
i don't know what mower this came off of the guy said there were no name on it.
but the number on the switch is 3497644, i can't find one. is there a replacement for it.
i have a kawi. motor, i pulled the fuel pump and the plunger won't move when i turn it over.
also it won't start on spaying starter fluid in carb.i know you will want the numbers on it but i can't find any/
its off a john deer mower and its water cooled.
i have a toro 71184 ssn. 5913447 and on the deck it has a bell crank, i can't find a good diagram of how the inghage cable goes from the handle to the bell crank.
there are two plastic pulleys. i must not have the cable on right because there i a lot of slack in the cable after i disingage the...
ibought a brand new carb for it and it still won't start. put my finger over plyg hole. and it has comp. i tried adj the carb.
started at 1and a eighth turn, nothing. it seems the plug is not wet. so iam lost. ANY SUG.
i have a 5hp horz. briggs, and it needs a new carb, one of the legs broke off and i can't bolt it back on the motor.
my problem is putting it back together. there are so many linkage and iam not sure where they go. is there a diagram
fhat shows where they go, i downlowed a diagram but it just...
I have a 8hp briggs vert. engine and i can't find a throtle control plate anywhere, ebay, parts tree.
does any one know where you can still get one. its mdl# 1707-1515-01 code # 88011610
thanks.
I have a stx38 black deck, and i put a new drive belt on and it runs fine but now iam having trouble shifting gears., i have the brake in the whole way but it seems like its not enough. is there ans adjustment, all it does is put slack in the belt right!
REPLACED THE IDLER PULLEY BRACKET AND I NEED TO KNOW WHERE TO HOOK UP THE TENSION SPRING, EVERY MANUAL I LOOK AT SHOWS THE SPRING BUT NOT THE LOCATION.
CAN ANYBODY DRAW A PICTURE OF WHERE IT HOOKS ONTO THE FRAME AND IDLER BRACKET.
i have a 11hp briggs vert. engine old type with the solid type carb the number is 252707 0660-01
and where you have the control plate for the throtle and choke. One of the small holes that hold the plate on is stripped.
do you think jb weld will hold new threads.
I have a snapper rear engine rider wit a 8 hp briggs pull start on it and i want to convert it to a electric start. i need a electric flywheel but they are no longer avable,
they do have the ring gear, they say bolts on the bottom of my org. flywheel. but dosen;t it have to have magnets in it...
it seems like it is getting fuel throu the carb but the plug is bone dry,
and when i put the ing. checker on i get fire to the plug but not through it i tried several plugs. i think its because the head is alum. and can;t get a good groound.
ius there any other way to check the fire.