Search results

I checked that and there was no excessive play in the throttle shaft.

That tumbling is a great idea. I used to shake the tanks by hand with nuts and bolts in them and dunp it out in a tray andwipe the bolts with a rag and put them inside the tank again for more shaking.

So after you tumble it with the nuts and bolts just use soap and water to rinch it? thanks.

I thought that type had a check ball because I could blow in to the long tube but could not suck the tube so that is because the flapper valve thanks.

Also those tubes have a check ball in them.

How do you remove them.

I was referring to the piece with a hole in the side of it that is casted on the carburetor. I took the carb off again and sprayed carb cleaner in it again and blew it out with air and now it works fine thanks.

I tr ied reading the manual but my screen reader does not read it properly

On the carburetor how many holes should be in the small pickup that fits in the shallow hole on the fuel tank.

Befor I replaced the gasket to block I noticed there was 2 gaskets on there so I scrapped them and tried 1 gasket. It speeds up slightly but full throttle it dies.

I replaced the pump diaphram so I will try a new carb gasket thanks.

I am working on a briggs tiller model 130297 type 301501 code 88090207 and I replaced the tank gasket and the diaphram and it will idle fine when I adjust the needle valve but when I try to speed it up it stalls. I made sure the long tube was clear and I cleaned the hole in the side of the part...

Thank you I fixed the problem.

I am working on a Cub 1330 where the person put the arm that has the idler wheel for the belt tensioner for the mower drive belt in the wrong place. I know it is bolted to the under frame of the mower. I reattached it to the threaded hole on the mower chasis but I can't find a hole for the...

The starter has bushings on both ends nothing else supports the armature.

I am going to buy one from amazon they are around 50.00 thanks for all the sugestions.

I have to glue a magnet on the case.

I already drilled 4 holes in the end cap that has the brush holders on it thanks.

I saw the video using u shaped pieces but there is no holes to put them in to hold the brushes in.

There is no holes in the brush plate

There is no holes to put a wire in to hold the brushes back

I am replacing armature on a kohler starter 2009811-s and I am having trouble holding the 4 brushes in so I can put the armature in the end piece. How do they do that thanks.

I did not mow with that one I only repairred it. I put a different muffler on it and it is a little quieter and the customer said it was better.

thank you

I was wondering what to torque the replacement rood too thanks.

I finally got it. I used a short socket on a small swivel extension thanks.

I am replacing connecting rod on a Kohler 21 horse courage engine but can't get socket on inner rod bolt. The counter weight balancer is not allowing me to get a socket and wrench on the bolt. The engine is model sv600 spec sv600-0009 serial 371311993

your right The replacement one I bought was a nikki and it runs better.

I have a briggs 19 horse on a yard machine rider and the engine is quite loud. I have a round muffler which bolts to a short pipe which is bolted to the head. The muffler and pipe are good but as I mensioned it sounds loud when it runs. The muffler comes out of the engine on the right side and...

I had a other mechanic look at the carb and it was clean and the gaskets were good. I put it on the engine and it still surges so I am going to put a worburo carbutor on it.

It is a briggs engine model 287707 type 7224-01

I noticed that when I close the choke it runs better and at a higher speed like must be starving for fuel.

I am working on a Cub mower which has a Micki carb 698620 and I took it apart and cleaned iit but it still serges. If you hold the throttle with your finger it runs better. I have another enging with that same carburetor on it which does the same. They are a bad design carburetor that briggs used.

It is the starter with 2 studs on top. I finally got it you have to position the wire which also fits in the same slot. What a pain.

I am putting a new starter in a Kohler sv590 and the new starter has a tab that sticks up near the studs and the starter won't seat right because the tab hits the piece that the studs are supposed to go through. The old starter did not have that piece.

That is what I did but it was going in too hard so a machine shop friend looked at it and he said the screw that was in the new spring I got is too big diameter for the hole so he let me borrow a 6.1 metric tap and it worked fine.

I figured that but the screw was going in too hard and I was afraid of braking it off.

I found out there is a small piece that slides off which has a opening to get to the adjustments. On the replacement cylinder I bought the hole that the vibration spring screw goes in is not tapped. It is a 7.100 metric tap sice. Is that a common size or is it special size.

I got it running but how can I get to the adjustment screws after I put the air cleaner assembly in there is no hole to get to the mixture screws.

I think it will work now sinced I cleaned the fuel pump section again

I have a husqvarna k750 which has new cylinder, piston and rings and new crank seals. It will run if you squirt fuel in the sparkplug hole but it does not seem to suck the fuel up from the tank. The fuel filter is new and fuel is getting to the carb when I take the line of f fuel runs out of the...

Thanks I tightened the float bowl and it starts better.

I am working on a mtd snowblower with tecumsah 10 horse on it model lh358sa and when I prime the engine with starter fluid it keeps running fine. I shut the engine off and try to start it a few hours later it does not start on choke or by pressing the primer. I tried another carburetor on the...

I finally figured it out but I have to find the size of the bottom belt that goes from the 2 blade pulley to the center drive pulley.

I am trying to put a mower deck on a gravely 1138g and the diagram I got does not show how the 2 arms go or how the lifting carriage goes on the deck or the mower. Where can I get a picture of the entire assembly thanks.

I am working on a scag z mower and when it is running I get a rattling sound but it is not from the engine. The drive belt shows sign of wear on the wide part of the belt. How do you access the top drive belt pulleys, there is no room underneath?

I put grease in the seal to hold the spring and I cut a piece of a plastic container and put it inside the seal and it worked perfectly thanks for the great ideas.

I am working on a twin cylinder briggs 23 horse engine. I am trying to replace the crank seal on the power take off side of the crank. I am having a hard time getting the seal on the step part of the crank where it gets wider. Once I get it past that part I can tap the seal on with a plastic...

I am working on a Bradley 48 inch walk behind hydro mower and there is no room to get behind the engine bottom pulley in order to get the mower belt off the pulley. The belt guide and idler is not acdcessiable. Is there something I am missing?

I am working on a briggs model 21t202 and am replacing the connecting rod and I would like to know which way does it go on the piston. I know the arrow on the piston goes toward the flywheel.