Search results

Great neighbor !!!! Follow ups are always appreciated, how we all learn.

This worked quite well !!!

This worked quite well !!!

Just - I cannot help. But if you post good pictures of the tractor and the axles, maybe someone here can help.

OK, here's my current solution. I drilled a hole, attached a 5/16" eyebolt to the handle; I peened the inner surface of the handle in, and replaced its padding with some new pipe insulation, so I can still pull the wagon manually without the end nut digging into my hand. Then I circumcised...

OK, here's my current solution. I drilled a hole, attached a 5/16" eyebolt to the handle; I peened the inner surface of the handle in, and replaced its padding with some new pipe insulation, so I can still pull the wagon manually without the end nut digging into my hand. Then I circumcised...

Return/warranty. Should not be your issue/worry !!

Well, "sometimes" bigger IS better !!!

Thanks, I'll figure out something. I'll likely use like the a couple of times a year at most. A piece of perforated 1.5 inch square tubing like 2 feet long looks promising as a temporary substitute for the lawn tractor handle...

I added a spring from the hardware store to the carb of my B&S engine, as the choke spring wasn't strong enough to open the butterfly when I moved the choke lever after a few minutes; so it ran rich and died until I modified it.

Actually, I do have a 5/8 inch long bolt I tried on the lawn tractor to try using for our drag harrow for the horse arena (but the lawn tractor didn't have enough power to pull that through the soft sand). For that, I just looped its ball over the top of that bolt. Thanks for the tip ! I'll...

Thanks, I have a much better idea now of what to do. The tractor plate hole and the pivot point for the graden cart handle are both about the same height, 8 to 8.5 inches off the ground.

I'm not sure that I understand. D shackles to what? One D shackle between the two horizontal holes on the cart handle? And then the other through the vertical hole on the lawn tractor plate? I'm trying to understand....

I'm trying to attach a garden cart I have to my Craftsman LT1000 lawn tractor; there must be a way, and I cannot Google anything because I don't know what it might be called. I have a Harbor Freight garden cartwhich has a handle 1.5 inches span but the holes for the handle are horizontal. My...

I'm trying to attach a garden cart I have to my Craftsman LT1000 lawn tractor; there must be a way, and I cannot Google anything because I don't know what it might be called. I have a Harbor Freight garden cartwhich has a handle 1.5 inches span but the holes for the handle are horizontal. My...

I knew absolutely NOTHING when I bought a Craftsman LT1000 in 2005, but had 1.5 acres of tumbleweeds at least knee high. Yes, Sears was unable to deliver this from the store on the designated day, could not arrange to do this no way, no how - I suggested paying overtime to drivers, renting a...

What about installing a simple shut-off switch like those available at auto parts store...

You mean like with the Craftsman $100 tile saw I purchased about 15 years ago. There was no display model, I bought one of the two they had a mile from my home, unboxed it, thought the alignment fence looked real cheap and plastic. It broke immediately. I swapped it out for the remaining...

Mine is a 2005 LT1000 with a Briggs & Stratton engine, and mine has an electric solenoid that shuts off and opens on the carburetor when it gets voltage.

27-35 ft lbs is also listed in the owner's manual for my 2005-purchased LT1000. I do admit that even though I have a torque wrench, I have never used it for the bolt/blade install.

I have a Craftsman 42" lawn tractor, purchased new in 2005. Mine has a B&S engine though. I haven't had issues with removing the blade bolts, but then in Arizona we don't get rust. I use a 1/2" drive ratchet with a 9/16" socket (six-sided). Yes, these bolts are tight, and supposed to be...

I agree with Rivets' reply

I have a 2005 model Sears Craftsman LT1000, purchased new. When I originally looked up the tractor drive belt and mower deck belts using the part numbers in the owner's manual, they were listed at about 1/4 inch different in length. Since then I just use A93K (½ inch x 95 inch) belt for both...

I have a 2005 LT1000 42" deck purchased brand-new, and one of my deck pulleys has always been at a slight angle.

GREAT !!! Thanks for posting the fix. I had a choke issue on my own 2005 LT1000; I added a small spring from hardware store to fix that.

Sure sounds like bad battery to me, if connections are all clean and tight. In the test above (battery voltage while trying to start), the minimum is 9.6 volts for automotive testing. Question: did you try a jump start using cables from your automobile? If it cranks/starts then you've...

Sounds like an issue for Dr. Phil or Dr. Ruth !!!!

I have 2005 LT1000. For some reason I suspect the carburetor, like possibly the electric solenoid/cut-off, maybe stuck choke.

A gal at work in the pilot manufacturing facility got her hair caught in a fan; she was lucky to have been unharmed.

Yesterday, I thought it would be a good idea to use a piece of steel wool on the bare rotating shaft of a vacuum cleaner motor, to clean off residue from a burnt/broken belt. The shaft grabbed the steel wool pad instantly, I was lucky to only bang up a finger. I ended up using cloth sandpaper...

Did you try to spray some aerosol starting fluid into the air cleaner or carb throat, then trying to start? Just may be needing this prime. If that doesn't get it to start - even for a few seconds - with several tries, then you need to check for spark; for that, you might need a helper.

For mine, R&R of the new engine was straightforward. Absolutely don't forget to add oil !!! As my new engine had an oil filter, I also made sure to order a spare. My engine takes Oil filter 2.25 in. high, OD 3.0 inches 3/4" -16 Thread Size [Oregon 83-013 B&S 492932 or 492932S (short) Kohler...

I have a 2005 LT1000 (917.275371) and mine uses "regular style springs" for that function. Left and right brake springs are same 131335 (superseded to 532179748). Idler spring is on the right and is 169022 (superseded to 532169022). Here's what my brake arms look like (disregard the...

I replaced the engine in my 2005 LT1000 lawn tractor a few years ago. The new engine came with an oil filter, bolted right in, was the best decision for me. Funny - I had starting issues for a couple of years on the original engine, even did the valve adjustment thing a few times; but the new...

I have LT1000 with B&S engine from 2005. I posted in another thread that I've experienced similar issues when my tractor's idler pulley wouldn't move readily due to dirt build-up. So cleaning and lube fixed that.

I've experienced similar issues when my tractor's idler pulley wouldn't move readily due to dirt build-up. So cleaning and lube fixed that.

I also have 2005-purchased LT1000 with the Briggs 31C707 engine. By early 2010s I also have issue of slow cranking, kept adjusting the valves, getting the battery checked or replaced, kept the battery on a charger. Then in 2013, apparently while mowing the weeds in the pasture, I developed an...

I have an LT1000 in a small town, and I order spindle, pulley, blades, belt as a kit. I always have a spare spindle/mandrel and belts on hand as these do wear or break. I've seen a John Deere unit that has grease fittings on its spindles.

That's what she had, what I installed for her; so she doesn't have to go near the battery.

Neighbor is 74-year-old widow, manufactured home on 2 acres, which she maintains. 1 horse, 3 dogs. She was going to discard, asked if I could work my "magic" to try to get it running. "We" are about a week in to seeing/testing if adding a trickle charger/maintainer (which she already had) to...

No, the lawn tractor is for the 1.5 acres of tumbleweeds and weeds (which really wreaks havoc on the lawn tractor blades). I'll be getting 1300 SF of grass soon, the "new" mower will be for that !

I'm getting my back yard professionally done in a few weeks, will have like 1300 SF of sod, but only have the lawn tractor up here. Out of the blue this morning my next-door neighbor rode her horse to the fence and asked if I would like her non-running lawn mower, that maybe I could get it...

Thx.

If solved, what was the reason/cause ???

Occasionally, I have to clean and lube the deck channel and idler mount (where the idler pulley mount slides, the part on the deck that moves when the engagement lever is moved upwards to move the cable).

Sure sounds like the incline is preventing fuel flow. Can you loosen the fuel cap temporarily and try? Might have to lower the gas level in the tank for this.

It sounds like the "Run" circuit only gets power in your "Run" position and not the "Start" position, why you need to catch it perfectly to get it to start/run. In cars and trucks, there are separate contacts in the electrical part of the ignition switch to "close"/complete the "Run" circuit...

I also say to check the choke, may be stuck in the open position. Anyway, at least you have a workaround.

You should be able to download PDF of the owner's manual, will have original part numbers, those can be Googled, lots of numbers have been updated. My own 2005 LT1000 lists drive belt and deck/blade belt as like 1/4" different in length, but I've used same belt length on both for a decade, way...

Wow, what a story about customer service run-around !!! Take it back like others have said, warranty issue. Does sound like an alternator/parasitic drain issue to me. When I purchased my Craftsman lawn tractor in 2005, it arrived without the deck support bracket on one side. Rather than...