Search results

It is a 3 amp charging system and not enough to keep battery charge and run electric clutch. You can change it by putting the stator for the 10 regulated system and the 10-16 amp regulator on it.

Good stainless will not rust. None of the Dixie Choppers rust and we have them that are over 25 years old. Mine is 24 years and no rust.

Does the Briggs have a regulator on it and if so how many wires does it have? Does it bolt on with one bolt in the center of the regulator or two on the ends?

Don't know if they do Kohler engines or not you may want to check this out. https://millennium-technologies.com/cylinderrepair/

It says some CH25-26 engines. Those are horizontal shaft engines. Did it also say CVs as well?

The problems will be as you stated the shaft size and the charging system. You can put a sleeve over the crank shaft to make for the correct shaft size. The charging system will need to be probably a 10 amp system...

CV25 with nickasil cylinder liners? Never saw a CV25 with that all I have ever seen have cast iron liners.

Religion is like this if you ain't sinning like I'm sinning you ain't sinning right. Good gosh I started this thread and it has turing into a pissing contest. I think it's about time to shut it down.

Right no 02 sensor on the Kawasaki EFI engines.

B&DS stopped manufacturing the Big Dog mower. Shame.

Why should we be the one who pays the bill for all the other countries?

https://www.harborfreight.com/80-watt-iron-plastic-welding-kit-60662.html

Funny how someone from another country thinks they know more than some one who lives here and gets their news that has already been filter through the fake news media.

What you are saying may be true but those early people that came here were not getting the hand outs and living off the government, they paid their on way. They were not a burden on the government as these are.

As long as the crank shaft diamater and length are the same you can mount a larger hp engine on it.

So what engine would you consider better?

Nice looking mower clean for it's age. Hope it gives you a lot of good service.

I have a special crimping tool to put the cable end on. It is made where you put the end in kinda of a cradle and you smack the crimper with a hammer. really tight crimp.

Had customer bring in a Troy Bilt mower. He had bought a chinese carb that came with the filter. Carb was the wrong one for the engine. Took his cheap chinese filter off you could shake it and the filter element was loose and would rattle around the in the housing. Boy that would do a great job...

Welcome to the forum from Tn.

Washington, December 2, 2022 One thing I have learned with this whole Biden adminstration if the Dems are accusing the Republications of doing something they are the ones doing it.

Don't see any single Hondas on riding mowers they make a really good GX series horizontal engine GC engines are so so..

We already have the laws present adminstration just refuses to enforce them.

Those are not the kind of people I am concerned with. It is the criminals that these countries are sending into our country. They are empenting their prisons insane assylums into our country. 300,000 illegals crossed into our country in the month of December alone. Congress is bringing articles...

I don't have a problem with legal immigrants. It's the illegals that are killing our country. The Dems want them because their policies are ruining our country and they are loosing their voter base, They want to make it legal of illegals to vote and the more they are the more congress men there...

If an American citizen lies to congress that is a felony and they can get jail time. If a member of congress lies to the American public nothing happens. Not the way it should be. I don't think politicians should be able to make up lies about an oppoinent.

If they threw them out of office there would be no politicians in Washington. If Bidens lips are moving he is lying. Look what they are saying about the border. The Border is closed? That is why Abbott is putting up more fencing on the Border. Biden sued Texas and the Supreme Court said they...

Have you thought about a new mower you might buy a new one for a little more.

To me the best sources of energy are hydro electric and necular.

Two things come to mind. Air bleed that is stopped up or a porosity in the body of the carb allowing it to draw more un metered fuel in to the cylinder.

What kind of superior after market gasket is better then the OEM gasket? I personally have never had an OEM gasket fail.

At what rate? Tn pays 27.4 cents per gallon Energy T.C.A. § 67-6-206(b)(1) also provides that a “tax at the rate of one and one-half percent (1.5%) shall be imposed with respect to gas, electricity, fuel oil, coal, and other energy fuels when sold or used by manufacturers.” T.C.A. § 67-6-704...

Yes it was a problem they also has a cam issue the compression release stop on the cam would wear off over time and make the compression rease not work. It would kick back and make an awful noise. once they fixed all that they had a counter balance problem. I have seen them break, knock the...

They listed a different serial number as well. Go to parts tree and on the starts page click on see all brands click on CC and utility vehicles and scroll down until you find the model and serial no you want. It is toward the bottom of the list.

https://www.partstree.com/models/volunteer-46e-efi-37am46ed710-cub-cadet-4x4-utility-vehicle-sn-1i018g-1i019g

Do not try to jump start it or charge the battery without disconnecting the battery. It can cause a voltage spike and blow the ECU. Over $800.

Yes that was a problem in the early days for the auto industry but the thing about it was you could carry cans of fuel with you. Trouble with EVs is you can't carry spare batteries with you. There aren't enough charging stations around and the infra structrue is not able to support the addition...

Kohler command twin with 2 cam housings? Never saw a Command twin with 2 cams. Only twin cam Kohler was the single Courage. It had an issue with cracking the block where the cylinder met the block because the top plate bolts worked loose. You might have had a twin Cam single cylinder Courage. I...

We survived the night no frozen water. Kept the water dripping all night. High today around 30. It suppose to be up to the 60's by the end of the week. Say warm and be safe.

Been there done that.

We aren't over it yet here in north middle Tn calling for 1 degree tonite. Then slowly start to rise over the next several days and up to near 60 by the weekend.

The JD Scotts mower was probably built by Murray.

Do any of you guys have a minimum amount you charge for repairs? Local JD dealer charges $100.00. Co-op $80.00. Trying to decide what to charge.

Just took my little dog out to do her doggie stuff. Glad when they built this hous they put a 2 foot over hang on the roof. This leaves a mostly 2 foot trail next to the house that is mostly clear where we can walk and not have to walk in the snow.

My thermoniter says it is 4 f roads have been scrape once and they layed down brime on Saturday. I know because I got behind the truck and had to go and wash my SUV to get it off. Just glad there was one open. Have not been out since and not going till it clears. Not going to drive an hour to...

We do a PDI pre delivery inspections on all the mowers we sell and set the Top no load speed on all out mowers.

Boss was approached by Sears to do their warranty work. He was all hiped up do it I took a look at what they paid for warranty work and told him I would not work for that. We don't do Sear warranty work. They were going to pay about 1/3 of the time it would actually take or even less.

Kohler warranty pays 1.8 Hours for both gaskets. Don't just replace the gaskets plane the heads as well. This is on verticle engines. Just did one that had to take the engine mounting bolts out and lift the engine up to get the muffler off. Clean up and all that 6 to 8 hours

Take your pick there only two manufactures making lawn tractors now. Husqvarna and MTD now Black and Decker Stanley. They own MTD, Cub Cadet, and Excel that makes Hustler and use to make Big Dog until they bought them out. Base models Run over 2K.

Kohler Command is the best single engine on the market. Too bad they quit making them. They just don't tear up. Biggest problem is carb issues and most of that is due to sitting with fuel in them too long gumming up the carb.