Search results

I have this riding mower that won’t move but it will catch a little bit every once in a while. I’m pretty sure it’s not the belt, not the pulleys, the manual move lever is pushed in so it can drive. I really can’t figure out what is the problem. Help appreciated.

I'm selling this craftsman LT1000 riding mower with a 48" deck, new carburetor, air filter, oil, battery, new headlights, and sparkplug. everything has been regreased and works how it should. view the listing here -...

I have a craftsman LT1000 and when I start it with a NEW battery that wasn't on a maintainer, half of the time it just turns to when the flywheel gets tighter and the starter starts squealing. I'm not sure if the alternator is worn or the voltage regulator is blown ( i can't locate it anyway)...

i just bought this carburetor yesterday, installed everything and it runs great... but its surging. It came with a few spare parts that I had no idea what they were. The mower had been sitting in a field for the past two years but we got it out and I replaced some stuff. Thanks for your time in...

I have a gray craftsman LT1000 with a 16HP Briggs and Stratton engine and there seem to be no sources to find the model number of my carburetor. Specifically, I am looking for the right float needle because the ethanol in the gas gummed everything up. No listings seem to have the metal piece on...

I just bought a John Deere RX75 riding mower and need help troubleshooting. It turns over with no problem, there is suction in the carburetor, and I replaced the spark plug but it still won't start. I will take the carb off tomorrow to deep clean it because it probably needs it but it won't...

my snapper sr1028 with a B&S 28A707 engine just won't idle smooth! it pulses no matter what the needle is set to (there is only one needle). and when it is a little bit below half throttle it the engine bogs down. any help would be appreciated asap, thanks.

I have a snapper SR1028 and I think it is getting too much gas. i just need the proper adjustments for the needles. any help is appreciated, thanks

I got a Snapper SR1028 a few days ago and yesterday I cleaned the carburetor because it had some crud in the bowl. I reassembled it and there was a lot of gas going to the carburetor now, which was a good sign because there was no gas going to the carb yesterday. I pull-started it a few times...

I got a craftsman T1600 yesterday and coming home, I noticed that it was smoking whitish/bluish smoke after it runs for 2 minutes, I'm not really sure what the problem is the seller said he had just replaced the spark plug, and changed the oil, not including the filter. any help appreciated! -...

Murray Briggs and Stratton 5HP Quantum Power Push-Mower blows white smoke and barely dies down after startup, I think the carburetor setup is messed up but I can't find any sources showing the carburetor diagram. Any help is appreciated. MODEL TYPE. CODE. 124702-3106-01 92042759 Lanerdude9

Murray Briggs and Stratton 5HP Quantum Power Push-Mower blows white smoke and barely dies down after startup, I think the carburetor setup is messed up but I can't find any sources showing the carburetor diagram. Any help is appreciated. MODEL TYPE. CODE. 124702-3106-01 92042759 Lanerdude9

my 5 HP CRAFTSMAN edger engine has a crack in the muffler and is crazily loud, this has been a problem ever since I got the engine 1 year ago. Is there a way to seal the crack without buying a new muffler? would super glue work or gasket sealer? engine serial code: 100202 0015-01 6811127...

my 5 HP CRAFTSMAN edger engine dies on full throttle for some reason, this has been a problem ever since I got the engine 1 year ago. maybe it has something to do with the leak in the muffler? I have tried adjusting it and it still has the same problem, but ONLY on full throttle. I have no idea...

MTD edger with a 3 hp briggs, how do I fix a seized briggs?????? very hard to pull.