Recent content by Rivets

  1. R

    Ignition Coil

    To my knowledge I don’t think there is any way to convert that engine.
  2. R

    Time Cutter deck lift pedal

    Ok, but I would stop and pick up the ball and keep my cutting height equal and looking good. I just in your case speed overtakes looks. To each his own.
  3. R

    Time Cutter deck lift pedal

    To be honest with you, I’ve never heard of the deck lift being used this way.
  4. R

    Time Cutter deck lift pedal

    Sorry to ask a stupid question, but why are you trying to adjust deck height with the control arms in the run position? If you use the deck lift pedal, when the arms are out, you should not be making contact with them.
  5. R

    Never take their word

    In all my years I think I’ve seen just about every different flammable fuel in a small engine tank. Gas, diesel, acetone, lacquer thinner, mineral spirits, etc. About five years ago local station was found to have over 50% of their 87 Octane fuel to contain water. Had 25-50 lawsuits because...
  6. R

    wont run, smokes like crazy

    Carb solenoid will not cause this problem. Their function is to close the main nozzle to prevent after fire when you shut the engine down only. They do not control the amount of fuel entering the carb.
  7. R

    Old engine wont idle

    Don’t see anything wrong.
  8. R

    Off topic.. Reading a micrometer

    Believe it or not I laid In bed last night and this thread kept running through my mind. Am I making a mistake? YES. Being that this is a vernier micrometer made me not believe my own eyes. Sgkent is correct, I am wrong, another learning experience, not a mistake. Sorry to the OP for leading...
  9. R

    Right front drive wheel wont disengage.

    Might take a little hammer persuading.
  10. R

    Off topic.. Reading a micrometer

    sgkent, you may be correct, but as you said the picture is not very good. If it were as you said we should be able to see a line between 20-0, which would indicate 20-25. I don’t see that, which is why I taught my students read what you see, not what you think it should be. More than likely...
  11. R

    Solenoid

    What does a picture have to do with solenoid bolts? A lot. We are not standing next to you with a strong drink in hand, which you provided, nor do we have ESP. Your description doesn’t make sense, as PT pointed out, so a picture will help us help you. If this is to much work for you, there’s...
  12. R

    Off topic.. Reading a micrometer

    I taught my students to read a mic this way. 1. Numbers running left to right are dollars. 2. Lines between the numbers are quarters. 3. Lines going around the thimble are pennies. 4. Lines on the barrel (1-10) are tenths of a penny. The reading in you original post is this. 9 dollars...
  13. R

    Blowing fuses with key off

    If the key switch was directly shorting from the B terminal to the G terminal, this would cause the problem. If it shorting through a different terminal then you will need to do more troubleshooting.
  14. R

    Right front drive wheel wont disengage.

    Sounds like the drive pawl is jammed. Probably filled with dirt. Remove the wheel and you will find the drive gear. Remove the retainer clip and slide the parts off carefully, observing the order and direction they face. Clean and reassemble.
  15. R

    Blowing fuses with key off

    Yes a bad key switch can contribute to the problem, but you’re going to have to do some electrical troubleshooting to make sure.
  16. R

    Simplicity Legacy went on fire near battery!!- Please Help!!

    Probably caused by a spark into a mouse nest. If I remember correctly the gas tank is right above there. Looks like a major rewiring job.
  17. R

    wont run, smokes like crazy

    Sorry Slomo I have to disagree. They give people a false sense of security and if they forget to shut it off the problem rears it’s ugly head again. I can’t count the number of times I’ve seen them on a unit and the customer thinks they solved the problem when they installed them.
  18. R

    2014 Kohler command pro CH742 questions.

    All studs should go in approximately the same distance. This manual should help you. https://www.mymowerparts.com/pdf/Kohler-Service-and-Repair-Manuals/Kohler-Service-Repair-Manual-Command-CH18-CH20-CH22-CH23-CH25-CH26.pdf
  19. R

    wont run, smokes like crazy

    Only if you want a DIY bandaid fix and not solve the problem.
  20. R

    wont run, smokes like crazy

    I would check the oil level again. If it is overfilled and smells like gas, the float needle in the carb is stuck open allowing fuel to flow straight through the carb and into the engine cylinder and block. Fix is to rebuild the car with a new float needle and seat. Plus, remove the spark...
  21. R

    Mower won't start

    You don’t give us a lot of info to go on, but I’ll give you a couple of things to try. Your problem may be in the charging system, starting system or safety system. When you post back make sure to include all model and serial numbers from the unit and engine, so we know what you have. This is...
  22. R

    Blade timing matter? Cub Cadet 2166 42" deck

    On a system like yours there is no timing of the blades, which means you have no problems. The blades will constantly change their relationship to each other due to minimal slippage of the belt. If you did have a “timed” system, you would need a clogged belt and different pulleys.
  23. R

    Briggs v twin valve seal

    You are purchasing an unknown gasket set off EBay and then asking about replacing valve seals from that set because you think they might be a “MADE IN CHINA” seals in that set. To me it’s a no brainer, if I’m going to use that set I’m going to trust all parts in that set. On top of that I’m...
  24. R

    Old toro custom Briggs and Stratton engine

    Post the model number and serial number of the mower. From there we can get the engine numbers.
  25. R

    Fixed it too good?

    The green wire coming off the coil is the kill wire. Trace that wire and you should find a shutoff switch. That connection is probably part of the charging circuit.
  26. R

    Lawnboy Duraforce 10424

    First thing I would do is pull the muffler cover, not the muffler, and check to see if the exhaust ports are open. Personally I would pull the carb and give it a good cleaning, plus replace the float rod and seat.
  27. R

    Will not start

    What is the voltage at the cable ends, both at the solenoid and at the starter. Thinking either a bad solenoid or starter.
  28. R

    1998 721

    Yes, I could be a blown head gasket, but I have a couple of questions. Did this happen just once or does it continue? Is there a loss of power, especially under load? What does The plug look like on the cylinder where you suspect the leak? Have you completely dried the area where the leak is...
  29. R

    Black/Dark Gas?

    I would be checking for foreign debris in the tank. Wouldn’t be a bad idea to pull the tank and give it a good cleaning.
  30. R

    Customers can be a pain at times.

    This is why I always call the customer first if costs are going to run over push mower repairs over $150 and tractors over $200. Explain what I’ve found and I may find other things wrong. I try to find out if they had any other concerns. They decide how they want to proceed. It does take time...
  31. R

    Fixed it too good?

    He needs to find a kill wire coming from under the shroud before he can add a kill switch. Being a battery start engine I may be on the other side. Once he finds the wire, I’ll bet he finds a kill switch.
  32. R

    Recycler 22 fuel filter

    Toro push mowers do not come with an inline fuel filter.
  33. R

    battery string trimmer

    Echo 58 V trimmer.
  34. R

    older b+s intek 6.5hp on troybilt super bronco having issues

    Leak in tank shouldn’t affect your problem. Post engine numbers and we might be able to find you a service manual.
  35. R

    Fixed it too good?

    There is no shut off switch on the throttle control. Are there any wires coming out from under the shroud?
  36. R

    Toro Timemaster missing parts

    Post the units model and serial numbers and we get you a parts breakdown. Then you can figure out what parts are missing. From there you can decide which route to go.
  37. R

    Model number needed

    Should start with 247.289050.
  38. R

    Fixed it too good?

    Please post a picture of the throttle control where it attaches to the engine. There should be a wire coming from the engine to this control assembly.
  39. R

    Model number needed

    Post the numbers you have Please.
  40. R

    Help deciding - Kubota, Bad Boy, or Exmark

    Exmark with the Loncin engines are just fine. It’s just some people worship them and others won’t own one on a bet. Order I would put them in is Kubota, Exmark, Bad Boy. All decent units. Best thing I can tell you is give each one a good test drive, talk to the dealer about why his is better...
  41. R

    20 year old Kubota or new residental zero turn ?

    Even though I would normally recommend the Kubota over 50% of the time, but depending on condition and what part of the country you’re in, I think it might be a little on the high side. Check out this site. https://www.tractorhouse.com/listings?keywords=ZD21
  42. R

    SV590-0220

    Look at a 12-757-27-S.
  43. R

    MagnumMZ Trans axle issue

    If the belt is worn or tensioner is not applying enough pressure the belt may be slipping on one hydro.
  44. R

    MagnumMZ Trans axle issue

    The first thing I would check is belt and idler pulley condition. When was the last time you changed the belt and idler pulley and tensioner arm are in good condition and moving freely.
  45. R

    TroyBilt Garden tractor with defective Kohler engine

    This thread is getting very confusing to me. To me, either your repair shop is very Incompetent and giving you a line of BS or we are missing valuable parts of the story. A repair shop that can’t find the reason a spark plugs electrode is being smashed shouldn’t be an authorized dealer. I can...
  46. R

    TroyBilt Garden tractor with defective Kohler engine

    HOW WARRANTY WORKS?? Customer brings a faulty unit into the appropriate authorized service center. Customer provides appropriate information proving unit is in a warranty period. Service Center diagnoses the problem and remedy. Service Center contacts manufacturer of their findings and...
  47. R

    JD 42" lawn tractor lurches

    I’ve also found that a bad or worn drive belt will cause this. When was it last changed?
  48. R

    TroyBilt Garden tractor with defective Kohler engine

    Have you contacted Kohler engine technical support directly at one of these two numbers. If not you have not, you have nothing to loose in doing so. If you do call them, have the following information on hand. Model and Serial numbers of the tractor All information off the Kohler ID tag...
  49. R

    IT won't start

    Classic example of a bad ground somewhere. Start by checking and cleaning all ground connections. Battery negative to chassis, solenoid to chassis if it is a three point solenoid, starter to block, etc.
  50. R

    surging when moving

    Tipping a push mower on it’s side will not fill the cylinder with oil unless you let it that wat for an extended period of time. Second very little fuel will leak into the cylinder.
  51. R

    Ventrac electrical issues

    Here’s the troubleshooting steps I would do in this order. 1. Fully charge the battery. 2. Take a battery voltage reading. 3. Remove the negative cable from the battery And let it sit for 24 hours. 4. Take a second battery voltage reading. If it is not the same as #2 you have a bad battery...
  52. R

    Do I want a zero-turn mower?

    You’ve got a real headache there. I doubt a Z-turn will save you much time. Depending On you budget, have you considered a stand on mower. Would definitely allow you to get closer to the trees and cut down your mowing time.
  53. R

    Can you reuse bolts

    You are correct.
  54. R

    surging when moving

    I’m betting that at .024” your surging is the result of a rich mixture. The largest I ever go is #77 drill or .018”.
  55. R

    Dana/Spicer 4360-55 locks up in lower gears

    I forgot to add that if you decide to repair it you should get the following parts. Axle seals and bushings. Many times Peerless transmission parts can be used in Dana/Foote units. I know this is a Peerless manual, but they are so similar that it many be of help...
  56. R

    Dana/Spicer 4360-55 locks up in lower gears

    I’ve rebuilt many of those units over the years and without opening it up I’m guessing that the shift keys are worn and being nearly 30 years old the lube is probably hard. Hard to guess what other part might be bad without seeing and feeling it in person. If you do open it up a word of...
  57. R

    Briggs and stratton opposed twin rebuild kit

    Your can get gasket set, carb kit, but as Scrub said all other parts are sold individually. Depending on how damagEd it is might look into the cost of a short block.
  58. R

    Cub Cadet Tiller Input Shaft Seized

    A little heat on the outside of the case, with a propane torch should also help. Will probably have to do a little repainting when done.
  59. R

    Can you reuse bolts

    No Loctite, and most head bolts are grade five, partially threaded. Just make sure they are clean, dry and in good condition. Also make sure the holes are clean and dry.
  60. R

    18HP Twin Vanguard, Horizontal shaft motor. Uneven surging issue

    Glad to hear the good news. Most guys never let us know the results.
  61. R

    Tecumseh 8hp, hmsk80, surges

    Have you checked the governor? If it is not set properly it will cause surging. Not uncommon for those older units to need a little tweeking.
  62. R

    Can you reuse bolts

    I’ve never had a problem reusing head bolts. Just make sure they are clean and dry before installing. New rod should come with new bolts.
  63. R

    Which ride on should I buy??

    You will get a lot of “I like” XXX brand over YYY because it’s never given me a problem. That being said I’ve gotten away from recommending any brand of low end tractors. This is what I recommend you do. 1. Never buy from a Big Box store, always go through a dealership. I don’t care if they...
  64. R

    Craftsman t110 crank no start

    But has you fuel sat longer than three weeks? White smoke to me indicates water in the fuel. Condensation will build n the gas can very quickly in humid conditions.
  65. R

    Cub Cadet Tiller Input Shaft Seized

    On the shaft he is trying to remove, yes 100% are either bushings or ball. Don’t go away mad because you lost this one, just know you can’t win them all. I know you’ll see this as you can’t really stay hidden.
  66. R

    Cub Cadet Tiller Input Shaft Seized

    Look at the shaft he’s trying to remove, to me it sure looks different than the one you posted. That being said, seeing your this forums resident expert and love to point out other members mistakes, I guess I must be wrong again. You can start ignoring me again, because I’m not going away, and...
  67. R

    Cub Cadet Tiller Input Shaft Seized

    Those bearings are not on the input shaft.
  68. R

    Lawn Boy z340 zero turn parts/repairs HELP!

    To purge many systems you may have to go through the purge sequence 10-12 times. I’ve had ones that took me 2-3 hours, working it back & forth. Even had one which I had to let it sit overnight and start over the next day. You have to be extremely lucky to do one in less than an hour.
  69. R

    Craftsman t110 crank no start

    Did you leave gas in the unit all winter? If so, even with additives, I would remove all fuel and start fresh.
  70. R

    Cub Cadet Tiller Input Shaft Seized

    I’ve these trannys many times and have never seen needle bearings. Bushing 90% and ball 10%.
  71. R

    Cub Cadet Tiller Input Shaft Seized

    If there is a bearing in there it’s probably a ball bearing cheap press fit into the housing. If you provide us with the units model and serial numbers we would have a better idea.
  72. R

    18HP Twin Vanguard, Horizontal shaft motor. Uneven surging issue

    I see no reason to worry about a little rust on the flywheel or stator. If you have a pressure washer and air compressor or leaf blower, I would be using the to clean and dirt that unit. To bad you threw all that money into the fuel system.
  73. R

    Bolens Chipper/Shredder won't start....

    Your unit has a solid state ignited, so there is no way to accurately measure resistance. This manual may be of some help. https://www.mymowerparts.com/pdf/Tecumseh-Service-and-Repair-Manuals/TECUMSEH-SERVICE--REPAIR-MANUAL-3HP-TO-11HP-4-CYCLE-L-HEAD-FLAT-HEAD-ENGINES-692509.pdf
  74. R

    Bolens Chipper/Shredder won't start....

    Post the engine numbers so we know which coil you have.
  75. R

    Cub Cadet Tiller Input Shaft Seized

    If you brought me that cover I would clamp the shaft in the vise and soak that bushing with a rust breaker like PB Blaster multiple times. The oil in your picture will not breakdown rust. After sitting a day or two, while still clamped tight in the vise, I would grab the housing and slowly...
  76. R

    18HP Twin Vanguard, Horizontal shaft motor. Uneven surging issue

    Testing with the inline tester indicates to me you have an ignition not fuel problem. Looks to me like your going to have to pull the engine on that unit to access the coils. Sometimes you might get lucky and just have to remove the hood. No way to test todays electronic coils without special...
  77. R

    Stator

    Missed the HMA.
  78. R

    Stator

    No charging system on that unit. Battery is charged with an external charger.
  79. R

    Question

    Yes and I would recommend just about anything over those units. Just about the worst setup I’ve ever worked on. That being said some people loved them, but not me.
  80. R

    Z248F engine runs, arms unresponsive (50.8 hrs use)

    Could very well be, but a stick popping a drive belt off won’t be warranty. Check the simple things first, then check on warranty, may save a pickup charge and cost of labor, plus belt.
  81. R

    Lowe's (MTD) Tractor stuck in gear

    First thing to do is check to see if the belts are routed correctly. Second is to check to see if the bake is actually allowing the drive belt to loosen to allow shifting.
  82. R

    Z248F engine runs, arms unresponsive (50.8 hrs use)

    Three things to check. Broken drive belt, belt off tensioner pulley, tensioner pulley are stuck in a loose position.
  83. R

    Battery charger voltage?

    It will depend on the size of the battery your charging. Normally you need 10% above battery size. 6 VDC battery needs a 6.6 VDC charger, 12 VDC battery needs a 13.2 VDC charger.
  84. R

    B&S 500E-140cc FUEL STARVED

    According to the model number you posted, you need carb #799583. The code number, aka serial number, is 17 0509 51 34567. Forget the spaces.
  85. R

    Tubeless flat tyre

    Under the rectangle frame will be not problem.
  86. R

    Where do you add oil to rear end on a YTA00V46?

    Please double check your model number. Look under the seat.
  87. R

    Question

    I know of none. The way Z-turns are designed non hydros would not work.
  88. R

    Troybilt 31AH55R5711 Storm 3090 Electric Chute Directional Control troubleshooting

    Thank you, but that one’s a little to high end.
  89. R

    Oil in oh?

    To provide lubrication!!??
  90. R

    Troybilt 31AH55R5711 Storm 3090 Electric Chute Directional Control troubleshooting

    I probably just got lucky. I’d take you up on your offer, but would probably break your bank, as I only drink high end juniper liquid straight up on days which end in Y. At my age you need to know how to be careful. Good Luck next winter.
  91. R

    Burning oil.

    I’m going to get asked over the coals for this, but here goes. According to the owners manual and service manual for Kohler‘s EFI engines you should be using a 10W-30 oil, not 10W-50. Second I don’t understand 4 oil changes in 56 hrs, if your burning oil. One change after breaking and a...
  92. R

    What piece of equipment to rake/clean this lawn?

    I use a tow behind spring tooth rake every spring. One neighbor has a rake, one a lawn sweeper, and a third a trailer. Six of us put our backs together and weather permitting get 7 yards done in one weekend, weather permitting.. This year weather forced us into two weekends, but that meant...
  93. R

    Toro Recycler making terrible noise only w/blade installed

    In my opinion you may have problems down the road. I don’t like thread lock and split lock washers on blade assemblies. Manufacturer just calls for a bevel washer only. That being said it’s your unit and you can do as you want.
  94. R

    Deck Belt

    No brainer if you’ve done any searching on this forum. 95% of the experienced techs here will say OEM.
  95. R

    Problem with small craftsman tiller

    Because you supply us with so little information as to the model of the trimmer and engine, I’m only GUESSING as to what your problem is. Sounds to me like the carb is in need of fuel to get from the idle circuit to the full throttle circuit. Many times this can be resolved by adjusting the...
  96. R

    18HP Twin Vanguard, Horizontal shaft motor. Uneven surging issue

    Before tearing into the carb I would be checking the ignition system. I know everyone is focusing on a fuel problem, but a chaffed spark plug wire or kill wire would have the same symptoms. I’d be hooking my inline spark testers to both plugs and make sure that I wasn’t losing spark to one or...
  97. R

    Ariens Apex 60 dies after engaging deck

    I would be checking the deck belt, spindles and clutch, but have a few questions. 1. Does it die slowly or just shut off? 2. When was the deck serviced last? 3. Have you released any deck parts recently?
  98. R

    19hp B&S CAST IRON FLYWHEEL COMPATIBLE WITH 16 B&S ENGINE

    Short answer, NO. Swapping a cast iron flywheel to an engine with an aluminum flywheel will not work. Plus magnets are probably in a different position.
  99. R

    Z248F DRIVE

    The one thing you’ll never know is if the first shop you took it to changed the belt and routed it wrong. If they replaced the motors and routed the belt wrong, it wouldn’t work properly for them. They threw in the towel and you had to go to a second shop. I hate to say this, but there is a...
  100. R

    Toro Recycler making terrible noise only w/blade installed

    I’m guessing your problem is caused by a combination of the use of never seize and a bad blade adapter. I personally never use it and never recommend it, but others on this forum call me a crazy old fart.
  101. R

    Troybilt 31AH55R5711 Storm 3090 Electric Chute Directional Control troubleshooting

    You are using the same cleaner I use, but I’d like you to go one step farther. Spray the switch with the cleaner, trying to get cleaner into the switch, then work the switch vigorously to clean the internal contacts. Repeat a couple times and then install in the system and test. If this does...
  102. R

    Kawasaki FD460V Air Filter Causes Surging

    Governor “seems” operable and operating at the proper speed are two different things. An engine not running at the proper speed, especially idle, will surge the same as a lean fuel mixture. Engine speed and fuel mixture need each other and must play nice to eliminate surging.
  103. R

    Marketplace find

    Using the numbers off the tag, this manuals might help. https://www.manualslib.com/manual/60452/Generac-Power-Systems-190-220.html?page=21#manual
  104. R

    Motor starts to go up and down after half a hour

    Then I’ll back out of this thread.
  105. R

    Motor starts to go up and down after half a hour

    I’m sorry to have to post this, but if the ideas Scrub posted do not fix the problem I suggest you find a good mechanic or shop to solve the problem. Your not understanding of how an engine works could very easily cost you more money in the long run.
  106. R

    Toro Recycler making terrible noise only w/blade installed

    If the engine runs good with no blade attached, you problem is in one of the areas I posted.
  107. R

    S130 And MowerPlus Smart Module Won’t Connect.

    Duh, I meant to ask them for help troubleshooting the problem.
  108. R

    Troybilt 31AH55R5711 Storm 3090 Electric Chute Directional Control troubleshooting

    Do you have a multi meter? Need to check the switch first. If the switch is operating properly, need to clean all connections.
  109. R

    S130 And MowerPlus Smart Module Won’t Connect.

    Only thing I can tell you is to contact JD tech service directly. Your JD dealer should be able to give you a number if they can’t help you. Might have to apologize for not going through them when you purchased the unit. Time to bite the tip off your tongue. Another reason to using a dealership.
  110. R

    S130 And MowerPlus Smart Module Won’t Connect.

    300 series uses JD part number BUC10537. 100 series uses JD part number BUC10510. According to this site it is not used on an S130 unit...
  111. R

    S130 And MowerPlus Smart Module Won’t Connect.

    If the dealer couldn’t get it until 2023, how do the big box stores get it? Somethings just don’t compute to this old farts brain. I’m totally confused.
  112. R

    Basic Carburetor Adjustments for Toro Super Recycler Electric Start 20384

    You have a mower that I’ve recommended for the last 15 years and I’d like you to check a couple of things first. 1. Next time you try hot starting, remove the air filter cover and filter and check to see if the choke is open or closed? It should be open. If it is closed, the auto choke is...
  113. R

    S130 And MowerPlus Smart Module Won’t Connect.

    There are two different modules available, one for a 100 series and one for a 300 series. Do you have the correct one? Another reason to purchase from a dealer.
  114. R

    Kawasaki FD460V Air Filter Causes Surging

    Got more questions. 1. Are you sure the model number is FD460V and not an FB460V? Can not find the engine you listed. 2. Have you tried running the engine with no filter, just the cover fastened securely. This could indicate wrong filter. I’ve looked at an FB460V and the way the air filter...
  115. R

    S130 And MowerPlus Smart Module Won’t Connect.

    If you purchased both these units through a John Deere dealer, your best bet is to have them troubleshoot your problem.
  116. R

    Kawasaki FD460V Air Filter Causes Surging

    Three things come to mind very quickly for you to check. 1. Was it an OEM carb or cheap fleabay clone? I never trust or use clones unless I’ve got no other solutions. 2. Are you using OEM filters? Same reason. 3. Are you over tightening the air filter housing causing and air leak? See...
  117. R

    No Compression

    He should know better if he’s anything more than a DIY guy. Now I’ll get ripped for questioning the post. Oh well, been there done that.
  118. R

    Oil coming from intake

    You don’t give us a lot to work with, especially when you have an engine which is unknown to most techs. Lifan engines don’t have a very good reputation and are often tossed as parts and technical help is hard to obtain. Most shops won’t touch them for this reason. I suggest you remove the...
  119. R

    Bad Surging 11 HP upright

    Two things I’ve found when working on engines mounted to generators. 1. If it has an auto idle system, engine idles when no load applied, this system is not working properly. It can’t detect load no load. 2. The governed top speed is not set properly. On generators, the governor controls...
  120. R

    No Compression

    Exhaust valve on a 2-cycle engine??
  121. R

    Toro Recycler making terrible noise only w/blade installed

    First, according to the model and serial numbers you posted you have a 21” cast deck mower, with rear wheel drive. That being said there are five things which you should check. 1. Make sure the kickers, mulch baffles, are tight and in good conditions. 2. Make sure the belt cover is installed...
  122. R

    Tire pressure for zero turn lawn mowers

    According to the owners manual 15 psi front 10 psi rear. I normally go 20 front 10 rear.
  123. R

    Carb linkage-How does the throttle linkage spring connect to clip?

    Push the vertically part of rod into the hole and then push the clip over the horizontal part of the rod. This setup wil not allow the rod to jump out of the hole.
  124. R

    Readjusting the governor's linkage on a kawasaki engine?

    I’m thinking it might be a model FD750D. Is that the number on the ID tag? The number you provided is a family number, not a model number.
Top