Recent content by Rivets

  1. R

    Kohler 8hp k181 no spark

    I made a mistake also, primary should be between 10-17 Ohms. I used reading for automotive coil. Secondary is the same. Don’t understand either why your meter would read 1 on all ranges???
  2. R

    Need a diagram for the insulation of the linkage to the carburetor for a Kohler courage 20 hp

    Try this manual. http://resources.kohler.com/power/kohler/enginesUS/pdf/18_690_01_EN.pdf?_ga=2.242062210.1658754340.1601335970-986432130.1601335970
  3. R

    Kohler 8hp k181 no spark

    To me those readings would indicate primary winding good, but secondary winding bad.
  4. R

    John Deere - 210 - Electric PTO Belt Replacement Help!

    Deck size will dictate the proper belt needed.
  5. R

    Smoke and oil from the exhaust

    Sounds like your oil got contaminated by gas. Pull the dipstick and smell, if it smells like gas, drain all oil and put in proper amount. Start up the unit and run outside, as you will have a fogging unit unti all residual oil/gas is burned away. Why did you rebuild the carb in the first place?
  6. R

    John Deere - 210 - Electric PTO Belt Replacement Help!

    Please post the model number for the unit, behind left rear wheel. Plus what size deck do you have?
  7. R

    Kohler 8hp k181 no spark

    The Kohler part number is A-235741-S, but is NLA. It has been superseded to part number 4775520, but run almost $200.00. Before purchasing a new stator (coil) I would measure the resistance on both the primary and secondary windings of your exi coil. To test the primary winding, disconnect...
  8. R

    D140 W/B&S 656CC V twin: Loses one cylinder intermittently.

    My guess would be that you have a coil or plug wire breaking do with either a hot short or hot open. I would check the wire for any visible breaks or cracks. Either way I would probably replace the coil. Please post the engine numbers, as I’m guessing because I can’t see which type of...
  9. R

    Kohler 8hp k181 no spark

    Please post your spec number, then we will know what you have. We’re not question your knowledge, just want to be sure when we continue to try to help.
  10. R

    Kohler 8hp k181 no spark

    That’s what I mean about automotive style coil. Has polarity, needs to be hooked up properly.
  11. R

    help with PTO slippage issues

    Triple check that you have routed the belt properly and the idler pulleys and idler arm are moving freely. Personally I don’t think the problem is in the clutch.
  12. R

    19HP Opposed Twin

    See this thread from forum review of tachometers. https://www.lawnmowerforum.com/threads/your-favorite-most-dependable-tachometer.58424/page-3#post-362572
  13. R

    Victa Vantage VCS464 148cc 550 series 4 stroke lawn mower High Crazy RPM Issue. Briggs and Stratton Engine

    Or the throttle cable running under the air filter housing is rubbing on the linkage or throttle?
  14. R

    Victa Vantage VCS464 148cc 550 series 4 stroke lawn mower High Crazy RPM Issue. Briggs and Stratton Engine

    And what’s your problem? If you post back include the engine numbers located on the shroud above the spark plug.
  15. R

    help...is my carb hooked up right?

    Can’t really tell from that video as we need to see everything from the governor arm to the carb. This service manual may help you out and if not post back with all engine numbers...
  16. R

    Air leak sound at shut down

    This should help you out. http://resources.kohler.com/power/kohler/enginesUS/pdf/32_690_01_EN.pdf?_ga=2.246256516.1658754340.1601335970-986432130.1601335970
  17. R

    blown head gasket and stuck valves in 2015 Toro Zero turn? Fix or buy new?

    That series of Kohler was basically a good engine, so I would take a serious look at rebuilding, depending on what parts you will need and their cost. This manual will help you decide if you think you can do the work yourself. I would price out the parts you figure you need and add $100, in...
  18. R

    blown head gasket and stuck valves in 2015 Toro Zero turn? Fix or buy new?

    I don’t like swapping engines because I very seldom know the actual history of the replacement engines. If you would provide us with the model and serial numbers for the engine, we would be able to give you a better answer as to how each of us would proceed.
  19. R

    No spark

    Please post model and serial numbers for both the unit and engine. That way we will know exactly what you are talking about.
  20. R

    Toro Model 20065 self-propel not working

    Before replacing more parts I would remove the drive key and spring and clean the grease off them, plus the hole and reassemble. When you reassemble, make sure that you install the drive gear properly. One side of the gear will have an R stamped in it and the other side an L. This with...
  21. R

    Kohler 8hp k181 no spark

    Checking a condenser with an Ohm meter is not a reliable test. If you replaced the coil, did you set the air gap at .010, unless you have a rare unit which uses an automotive style coil. If the coil is set properly, I would then check to see that the points are set to .018-.020”. If they are...
  22. R

    Toro 5060 blowing fuse's

    99% of electrical problems can not be solved by eyesight. Wires and components look good, but have internal problems. I have no idea of you electrical troubleshooting skills, but one of these manuals may help you out. May not be your exact unit, but the troubleshooting procedure will be the...
  23. R

    John deere z225

    One of these manuals may help you out.. https://docs.google.com/open?id=0B6NaqjIxWV1ySkZjTTA5TGltZEE https://docs.google.com/open?id=0B6NaqjIxWV1yZHlwUk9CWlNwYVE
  24. R

    Toro 5060 blowing fuse's

    Voltage output has very little to do with blowing fuses. I would be looking for a frayed or shorted wire. Which fuse is blowing? Include the model and serial numbers of the unit when posting back. Look under the seat for them.
  25. R

    Toro lx 460

    Also check your oil level.
  26. R

    Air leak sound at shut down

    Sounds like a blown head gasket.
  27. R

    Valve Spring Removal Tool for K-301

    These are the two styles which I have in my tool box. I may use them twice a year. I wouldn’t buy either unless I planned on using them a lot. Check with your local auto parts store or small engine repair shop. Might be able to rent one cheap.
  28. R

    Montgomery Wards WS-66 chainsaw

    Only info I can find on your saw. http://www.acresinternet.com/cscc.nsf/ed1d619968136da688256af40002b8f7/6e665a4b7e8dec1f88256ced001f4ccc?OpenDocument
  29. R

    Axle Seal Loose on Husqvarna

    Couple of questions before we can help you. Please post the model and serial numbers for your unit so we can see what you are talking about. Can you tell us which side of the tranny are you talking about? How long has it been loose and how much fluid do you think leaked out? Remember we are...
  30. R

    Briggs and Stratton 650

    Nobody ever said I’m good, most say the opposite. To the OP, as stated, time to remove the carbs and give them a good cleaning, plus rebuild with Briggs part number 398188.
  31. R

    Briggs and Stratton 650

    Got any model numbers to give us an idea of what you are talking about, as the COVID-19 has screwed up everyones ESP. Look at the flap over the muffler.
  32. R

    Montgomery Wards WS-66 chainsaw

    Can’t find anything thing in my files on a saw with that model number. Montgomery Wards did not buil chainsaws, but sold the vast majority of saws built by Remington. Mighty Mite was the most common rebranded model and many used a Tecumseh engine. In its early hay day it used a fairly descent...
  33. R

    Hard starting New T10 Craftsman

    Check to see if the choke is closing fully on startup. Wouldn’t be the first time I’ve seen a Craftsman not setup properly.
  34. R

    Toro m/n 51972 weed eater

    Your number is correct, big fingers resulted in my error. Sorry.
  35. R

    LED Light Install

    Please show us the switch you are talking about. I’m thinking that you should be able to just replace the OEM switch with a SPST non lighted switch.
  36. R

    Toro m/n 51972 weed eater

    I think you are correct in thinking you have received the wrong ring. Ryobi engines were used on those trimmers and Ryobi Part # 620161002 is the ring you need. Cost of a new ring is about $3.00 + shipping.
  37. R

    Is the Kohler Courage really that bad?

    Com’on now, who’s trying to change the subject? At my age I’ve got a hard time staying on topic. Don’t try to confuse me.
  38. R

    Is the Kohler Courage really that bad?

    Mr. Trump, Oh sorry Chris, I asked you three questions and instead of answering them you keep reverting to your opinions and not scientific evidence or facts. I answered your question on how I get my qualified opinion, would you please factually answer the questions I posed to you, if you can...
  39. R

    Is the Kohler Courage really that bad?

    I guess we agree on one thing, you are qualified to have your opinion. That opinion is based on two Courage engines and what you read on the internet. My limited qualifications are working on small engines for over 50 years and working in the industry for over 40 years. At one time I held...
  40. R

    Is the Kohler Courage really that bad?

    When you answer my questions with factional experience, I’ll answer your questions. According to your rants the only good engines produced were Maytag and Briggs models A through F, because all others had problems which needed to be covered under a manufacturers warranty.
  41. R

    Is the Kohler Courage really that bad?

    Chris, I’m glad to see that you believe the adage “If it’s on the Internet, it must be true”. You can believe what you want and you can post your beliefs, but IL, Bert, Scrub and I have been working in this industry far longer than you and we don’t use the Internet to get our facts. We base our...
  42. R

    getting signal to new solenoid, still won't engage starter

    I agree, time to replace the battery.
  43. R

    Ariens Zoom 42 won't go, mystery part?

    I don’t think that it is a part for your unit, just my opinion. Check to see if you might be missing the idler arm spring, which keeps constant tension on the belt.
  44. R

    Honda HRR216K10VKAA (Serial# MZCG - 1431747) drive belt replacement procedure

    Remove the pulley by removing the nut. I hold the pulley by squeezing the belt tight and using an impact wrench. You can then install new belt and tighten the nut.
  45. R

    Need wiring diagram for Duetz Allis 1613 12.5 hp

    Can you provide us with the model and serial numbers off the frame tag. With that we may be able to cross reference your unit to Simplicity.
  46. R

    Funny picture thread

    According to the Smokstac forum that mower was probably built by the Quick Manufacturing Co. around 1957 for either Rugg or Springfield.
  47. R

    What gap do I set the intake and exhaust valves to?

    Intake .004. Exhaust.008. I recommend setting them 1/4” past TDC.
  48. R

    Governor spring broken replacement part help

    The numbers we need are on the black & silver top on the engine housing.
  49. R

    Rough ride

    No need for a hug, just need to educate people. If you understand how the forum works there is no need For second thread. If you want your there to be viewed more just bring it back up with a reinforcement comment.
  50. R

    Rough ride

    Why the duplicate thread? No need unless you want members upset with you, which means they will do the opposite of what you would like.
  51. R

    kohler cv16s engine not charging

    This manual should answer your questions. https://www.mymowerparts.com/pdf/Kohler-Service-and-Repair-Manuals/Kohler-Service-Repair-Manual-Command-CV11-CV12.5-CV13-CV14-CV15-CV16-CV460-CV465-CV490-CV495.pdf
  52. R

    Craftsman mower 917.376060 with Briggs engine - sagging, surging now not starting

    Mower should have Briggs engine #123K02-0592-E1. Time to clean and rebuild carb with kit #398188. I use this procedure. Needle and seat replacement. Remove the carb, and then remove the float bowl. Check the float bowl jet (which is the bowl screw) and make sure the jets both horizontal and...
  53. R

    John Deere D140 wiring issue

    Are there two or four wires going to the switch? More than likely you have a normally closed switch. Try untwist them and tape them individually so there are now no connections, then give it a try.
  54. R

    I have a new areins 52" edge. Ran fine for a month but now it won't turn over I believe this unit has a solenoid when I turn the key I'm hearing the

    If it is only a month old I’d be talking to the dealer for warranty work. At that age even the battery should be covered. This year we’ve seen a rash of poor quality original batteries which don’t last three months.
  55. R

    Lawnboy 10515 Rear Drive Wheels

    That cover should NOT contact the wheel when installed correctly. Which means that recess means nothing. The step washer needs to be installed on the inside of the cover, between the wheel and cover. If the cover gets tight, something is installed incorrectly.
  56. R

    Lawnboy 10515 Rear Drive Wheels

    Two things I see real quickly. Way, way, way too much grease, clean everything off. Grease on these plastic gears does nothing but attract dirt, which will cause premature wear and failure. Second, you need a step washer in that gear cover. Without that washer the axle bolt will tighten down...
  57. R

    LawnBoy carb kit M-series

    Why two threads, you need to have a bit of patience.
  58. R

    Lawnboy M21ZPR 1989 carb kit

    Carb kits are not available, but most individual parts are. There are two carb numbers for a complete carb, 684274 superseding to 684548. Do a google search using these numbers to find a carb. This site may help with individual parts, using your model and serial numbers...
  59. R

    Lawnboy M21ZPR 1989 carb kit

    Please post the model and serial numbers from the ID tag.
  60. R

    The Biggest Mower on the Tightest Budget - What are my Options?

    First of all please don’t get made at me, as at times I’m to honest with my replies. Your $$$ amount and project sized are a bit unrealistic. Any mower you purchase in that price range, for that job, is not going to do a good job for you. On top of that I doubt it would last you five years...
  61. R

    Trimmer recommendation

    I have an Echo model SRM-266 and always recommend this model if you have the litt extra $$$. When my fathe-in-law past away I used it to clear three years of growth between his pine and maple trees. They were alternated plated in three rows, each row 250 feet long, so I could use a mower...
  62. R

    Learning on a 1980s Craftsman Edger - I have it running! Want to get it running better. Turns off with new air filter

    Go to Sears Parts Direct and type in your model number, they will get you a parts diagram. On the engine shroud, top or side, you will find a model number for the engine. You will the find the parts numbers you need.
  63. R

    Swapping wheels on a toro self propelled mower.

    Short answer NO.
  64. R

    troybilt tb320 running weak and spitting through carb

    If you didn’t properly torque the flywheel nut you may have sheared the key again. I would check that first and if that is not the problem please supply us with the engine numbers so we know what you are talking about.
  65. R

    Briggs and stratton carb question

    Not a fuel shutoff.
  66. R

    Learning on a 1980s Craftsman Edger - I have it running! Want to get it running better. Turns off with new air filter

    First thing I would do is get another new filter, as that one may look new but if it sat around out of the box it could very well be clogged due to moisture corruption.
  67. R

    Dixie Chopper LT2700 started blowing white smoke suddenly

    White smoke normally indicates water in the fuel, especially if it started after filling the tank.
  68. R

    Briggs and stratton carb question

    Please supply all engine numbers and if you live in California as sometimes with the newer models, that nipple will have a vent tube attached to it. Depends on the year and your location.
  69. R

    Say It Isn't So

    No one told me where he lives, just wanted to let him know that they are available.
  70. R

    New Toro w/ water in the oil

    Two things come to mind very quickly. First, I would be calling the dealer on Tuesday ( hope you didn’t purchase from a big box store) and find out what is going on there. Respectable dealers would have checked that before delivery. Guys like that make my blood boil, as they are no better...
  71. R

    Say It Isn't So

    Google search Lawn Boy part number 99-6713 and you’ll find starter assemblies.
  72. R

    Ride on mower HUSQVARNA needs help

    With a little more info we should be able to help you. Pictures did not load. A couple of things would help us help you. Resize you pics and try to post again. Check for numbers under the seat. Post all engine numbers. What size deck?
  73. R

    Frustrating blade search for Ikon XD 52

    30 degree is the angle of the cutting edge. Personally I would not use a blade that is a 1/4” wider, due to weight difference, but I’m sure he who is smarter than me will beg to differ. Remember you are spinning them at high speed, which will affect torque differences an possible bearing wear.
  74. R

    Toro Z420

    03 is just a sales number, you don’t have to worry about it. The w number is a manufacturing number, again don’t worry about it.
  75. R

    B&S Intek Dual Charging System - DC charging voltage

    In a perfect world Briggs would supply those specs, but as you know this world is not close to prefect. Sorry for wasting your time.
  76. R

    Frustrating blade search for Ikon XD 52

    Gravely doesn’t supply specs for its blades. You’ll need to take your blade, meas it and compare what you have to these specs.https://www.oregonproducts.com/en/blade,-bobcat,-gator-g3,-18%22/p/93-601
  77. R

    Frustrating blade search for Ikon XD 52

    My research tells me that the 04771200 blade DOES NOT cross to a Oregon 93-601. I could not find an aftermarket blade.
  78. R

    Toro Z420

    #106-2247-03 has an air lift of 1-3/16” medium #110-6568-03 has an air lift of 1-1/4” high Will probably have to remove the blade to check the numbers.
  79. R

    2-Stroke Jet

    I would check your local repair shop, as the should have a few of those old carbs laying around. That idle jet was the same for many different carbs. Might cost you a half dozen donuts.
  80. R

    Toro Z420

    Please post the part number for the original toro blades. It will be stamped on the blade. I’m wondering if it might be 110-6568-03 which is a medium lift blade.
  81. R

    B&S Intek Dual Charging System - DC charging voltage

    The only time I’ve ever seen a voltage reading over 15V, is when the battery is severely discharged. Normally a good charging system will have an output of 13.4-14.8VDC. Don’t know if this manual will help you, but it is all I could find on Briggs el systems...
  82. R

    Craftsman YS4500 Briggs and Stratton 21HP Intek Single Cylinder Problem

    He’s talking about me, because he knows so much more than me. That’s why you have to read and follow my signature.
  83. R

    craftsman mower isnt starting

    First check your battery terminals for cleanliness and tightness. Then check the battery ground to chassis connection making sure it is clean and tight. If you have a three terminal solenoid, the frame of the solenoid is you ground and when mounting it to the frame the surfaces must be very...
  84. R

    getting signal to new solenoid, still won't engage starter

    Run that same test at the battery. If it drops below 9V, bad battery. If it is 10V or more battery good and you must then proceed down the positive side, testing each connect to find where you have a voltage drop. Pain in the butt, just like most electrical troubleshooting. Patience and an...
  85. R

    Cutting deck timing pulleys

    If it were me I’d order part numbers 13, 14, and two of 28. I would replace both bearings. The far left on the bearing stud is the inner race of the old bearing, which you may have to cut through to remove if you can’t remove with a puller. Will need to use a cutting wheel, as it is hardened...
  86. R

    hi i'm new here but , have a lt1050 it has charging prob........?

    This manual should help you with testing the charging system. https://www.kohler-engine-parts.opeengines.com/pub/SM_3269001_SV710_SV715_SV720_SV725_SV730_SV735_SV740_SV810_SV820_SV830_SV840_REVISED_7_14G.pdf
  87. R

    variable speed pulley

    If the belt is loose check to see if the idler pulley tensioner arm is moving freely. The pivot point gets dirty and won’t allow the arm to keep tension on the belt.
  88. R

    Toro Proline 44" Model 30177

    Two things come two mind if it blows while mowing. First, I would check for frayed wires. Might find one that is shorting to ground as you are bumping around. Start a the clutch and work backwards. Tough to find with a meter, as it may not be touching, need to use your hands and eyes...
Top